Masterforce 12 inch drill press

Download PDF Manual:

Manual Masterforce 12 inch drill press.pdf

Text of Manual:

@2017 Menard, Inc., Eau Claire, WI 54703 ‘
0912017
1211 Drill Press
{Variable Speed)
240-0065
(l•lhi65N;tiMMM41J
[ACAUTIONJ To Reduc·e The Risk Of Injury, User Must ReadAnG
Understc;md Operator’s Manual. Save These Instructions For Future
Reference.
TABLE OF CONTENT
Safety Symbols ……. …. ….. …………… · ····· ··· ·· · · ·· · ···· · · · · · ·· · ….. … … … Page 2
Safety Instructions ……………………………………… ………………….. Page 3
Overview ……………………………………….. · · ·· · · · · ·· …………………….. Page 7
Specifications ……………………………………………………. …………… Page 8
Assembly and Adjustments ……………………………………………….. Page 8
Operation …………………………………… : ………………………………….. Page 15
Maintenance .. . . . . . . . . . . . . . . . . . . .. . .. … . . . .. . ……. .. . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . Page 17
Troubleshooting ·····························” ········································· Page 18
Accessories …………………………. ,………… ……. ………. ……. …… … . Page 21
Warranty …….. …………………………………………………………………. Page 24
SAFETY SYMBOLS
Some_ of the following symbols may be used on your tool. Please study them and learn their
meaning. proper interpretation of these symbols will allow you to operate the tool better and safer.
—–r— — –~—– —— — Symbol i Designation / Explanation

Name
Volts
Amperes
Hertz
Watts
Alternating current
Direct current
No-load speed
Pounds
Per minute
Class II construction
Read the operator’s
Manual
Wear safety glasses
Wear respiratory
Protection
Wear hearing
Protection
Wear gloves
Warning symbol
! Voltage
/ Current
I Frequency (cycles per second)
! Power
Type of current
Type or characteristic of current
Rotational speed, at no load
: Weight
Revolutions, strokes, surface speed
orbits, etc. Per minute
Double-insulated construction
To reduce the risk of injury, read
and understand operator’s manual
Operation of power tool can result in
foreign objects being thrown into eyes
Use of this tool can generate dust
which may cause respiratory injury
Noise from this product
can contribute to hearing loss
Wear gloves to reduce risk of injury
Alerts user to warning messages
This Symbol Designates That This Tool ls Listed By Underwriters
Laboratories, To United States And Canadian Standards
This Symbol Designates That This Tool ls
Listed By Underwriters Laboratories
This Symbol Dsignates ~hat This Tool ls Lista~ By The lntertek
Testing Services, To United States And Canadian Standards
This Symbol Designates That This Tool ls Listed By The Canadian
Standards Association, To United States And Canadian Standards
This Symbol Designates That This !~’ Is Listed
By The Canadian Standards Assoc1at1on
Page2
Is is to attract our attention to possible d_angers. The safety
The purpose of safety sym_bo ·th them deserve your careful attention and understanding.
symbols, and the _explanationi ~~emselv~s eliminate any danger. !he instructions and
The symbol warnings do not /n t s for propper accident prevention measures.
warnings they give are no su s I u e
1 AWARNING· i e to read and understand all safety insructlons In this
Be su~lert s mbols such as “DANGER” , “WARNING” and
manual, Including all safetyth· po.1er tool Failure to follow all instructions listed
“CAUTION” before using is ‘ I · I
below may ;esult in electric shock, fire and/or serious persona in ury.
SYMBOL MEANING
A_ SAFETY ALERT SYMBOL: _Indicates DANGER, v:’ARNING, OR CAUTION. H May be used in con1unt1on with other symbols or pictographs
,,,,,.ntrl§;I Failure to obey this warning WILL result In death or serious
injury to yourself or to others. Always follow the safety precautions to reduce the
risk of fire, electric shock and personal injury.
j & WARNING: i Failure to obey this safety warning CAN result in death or
serious injury to yourself or to others. Always follow the safety precautions to
reduce the risk of fire, electric shock and personal injury.
l A CAUTION: I Failure to obey this safety warning MAY. result In personal
injury to yourself or others or property damage. Always follow the safety
precautions to reduce the risk of fire, electric shock and personal injury.
Pagea
SAFETY INSTRUCTIONS
GENERAL SAFTY RULES
Safety is a combination of common sense,
staying alert, and knowing how your bench drill
press works.
IA.WARNING:! TO AVOID MISTAKES
THAT COULD CAUSE SERIOUS INJURY, DO
NOT PLUG IN THE BENCH DRILL PRESS
UNTIL THE FOLLOWING STEPS HAVE BEEN
READ AND UNDERSTOOD.
1. READ and become familiar with this entire
instruction manual. LEARN the tool’s
applications, limitations, and possible hazards.
2. AVOID DANGEROUS CONDITIONS. DO
NOT use power tools in wet or damp areas or
expose them to rain. Keep work area well-lit.
3. DO NOT use power tools in the presence of
flammable liquids or gases.
4. ALWAYS keep your work area clean,
uncluttered, and well-lit. DO NOT work on floor
surfaces that are slippery with sawdust or wax.
5. KEEP BYSTANDERS AT A SAFE
DISTANCE FROM the work area, especially
when the tool is in operation. NEVER allow
children near the tool.
6. DO NOT FORCE THE TOOL to do a job for
which it was not designed.
7. DRESS FOR SAFETY. DO NOT wear loose
clothing, gloves, neckties, or jewellery (rings,
watches, etc.) when operating the tool.
Inappropriate items can get caught and draw you
into moving parts. ALWAYS wear non-slip
footwear, and tie back long hair.
8. WEAR A FACE MASK OR DUST MASK.
Drilling into materials produces dust.
9. ALWAYS remove the power cord plug from
the power supply outlet when making
adjustments, changing parts, cleaning, or working
on the tool.
10. AVOID ACCIDENTAL START-UPS. Make
sure that the power switch is in the OFF position
before plugging in the power cord.
11. REMOVE ADJUSTING TOOLS. ALWAYS
MAKE SURE all tools are removed from the
bench drill press before turning it ON.
12. NEVER LEAVE A RUNNING TOOL
UNATTENDED. Turn the power switch to OFF.
DO NOT leave the tool unattended until it has
come to a complete stop.
13. NEVER STAND ON A TOOL. Serious
injury could result if the tool tips or is
accidentally hit.
DO NOT store anything above or near the tool.
14. DO NOT OVERREACH. Keep proper
footing and balance at all times. Wear
oil-resistant rubber-soled footwear. Keep the
floor clear of oil, scrap, and other debris.
15. MAINTAIN TOOLS PROPERLY. ALWAYS
keep tools clean and in good working order.
Follow instructions for lubricating and changing
accessories. See Maintenance section.
16. DO NOT operate the tool if you are under
the influence of drugs, alcohol or medication
that could affect your ability to use the tool
properly.
17. CHECK FOR DAMAGED PARTS. Check
for alignment of moving parts, jamming,
breakage, improper mounting, or any other
conditions that may affect the tool’s operation.
Any part that is damaged should be property
repaired or replaced before use.
18. MAKE THE WORKSHOP CHILDPROOF.
Use padlocks, master switches, and ALWAYS
remove starter keys.
IAWARNING:I DUSTGENERATED
FROM CERTAIN MATERIALS CAN BE
HAZARDOUS TO YOUR HEALTH. ALWAYS
OPERATE THE DRILL PRESS IN A
WELL-VENTILATED AREA. USE DUST
COLLECTION SYSTEMS WHENEVER
POSSIBLE.
ALWAYS WEAR EYE PROTECTION
_…~ . \’ti PR01te~
~vr ~
t~) ~l~~~
A bench drill press can throw foreign objects into
the eyes which could cause permanent eye
damage.
ALWAYS wear safety goggles (not glasses}.
Ordinary eyeglasses have only impact-resistant
lenses … they are NOT safety glasses.
Page4
LASER SAFETY
Toe laser light beam used . th· system is Class in is t n
Ill These lasers do not normally presen a
o~tical hazard, although staring at the beam may
cause flash blindness.
I A, WARNING:\DO NOT sT~RE
DIRECTLY AT THE LASER BEAM. A
HAZARD MAY EXIST IF YOU DELIBERATEL y
STARE INTO THE BEAM, PLEASE OBSERVE
ALL SAFETY RULES AS FOLLOWS:
• THE LASER SHALL BE USED AND
MAINTAINED IN ACCORDANCE WITH THE
MANUFACTURER’S INSTRUCTIONS.
• NEVER AIM THE BEAM AT ANY PERSON
OR AN OBJECT OTHER THAN THE
WORKPIECE.
• DO NOT PROJECT THE LASER BEAM
INTO THE EYES OF OTHERS.
• ALWAYS ENSURE THE LASER BEAM IS
AIMED AT A WORKPIECE THAT DOES NOT
POSSESS REFLECTIVE SURFACES, AS THE
LASER BEAM COULD BE PROJECTED INTO
YOUR EYES OR THE EYES OF OTHERS.
SPECIFIC SAFETY RULES FOR
BENCH DRILL PRESSES
I & WARNING: ~o NOT OPERATE
YOUR BENCH DRILL PRESS UNTIL IT IS .
COMPLETELY ASSEMBLED AND
INSTALLED ACCORDING TO THE
INSTRUCTIONS.
1. NEVER TURN THE BENCH DRILL PRESS
ON until the table is clear of all .foreign objects
(tools, scraps, etc.).
2. ALWAYS KEEP hands and finger~ away from
the drill bit.
3. DO NOT drill materials ~t do notbave a flat
surface-unless a suitable support is-used
(clamp or vise).
4. NEVER start the drill press with the drill bit
pressed against the work piece.
5. MAKE SURE the table lock is tightened
before starting the bench drill press.
6. NEVER layout, assemble, or set-up any work
on the table while the drill is ON.
7. MAKE SURE drill bit is securely locked in the
chuck.
8. MAKE SURE chuck key is removed from the
Page5
chuck before turning power ON.
9. ADJUST the table or depth stop to avoid
drilling into the table.
10. ALWAYS stop the drill before removing
scrap pieces from the table.
11 . USE CLAMPS or a vise to secure a work
piece to the table. This will prevent the work
piece from rotating with the drill bit.
12. DO NOT wear gloves when operating a
drill press.
13. BEFORE LEAVING THE MACHINE, SHUT
THE POWER OFF, remove the drill bit and
clean the table.
14. SET THE DRILL PRESS to the speed that
is appropriate for the material being drilled.
15. SHOULD any part of your bench drill press
be missing, damaged, or any electrical
component fail to perform properly, shut the
power OFF and unplug the drill press. Replace
missing, damaged, or failed parts before
resuming operation.
GROUNDING INSTRUCTIONS
1. IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provid13s the path of
least resistance for electric current and reduces
the risk of electric shock. This tool is equipped
with an electric cord that has an equipment
grounding conductor and a g!ounding plug. The
Rlug MUST be plugged into a matching outlet that
IS prQPSrly installed and grounded in accordance
with ALL local codes and ordinances.
2. DO NOT MODIFY THE PLUG. If the plug will
not fit the power supply outlet, have the proper
power supply outlet installed by a licensed
electrician.
3. IMPROPER CONNECTION of the equipment
grounding conductor can result in electric shock.
The conductor with the green insulation (with or
without yellow stripes) is the equipment
grounding conductor. If repair or replacement of
the electric cord or plug is necessary,
DO NOT connect the equipment grounding
conductor to a live terminal.
4. CHECK with a licensed electrician or service
personnel if you do not completely understand
the grounding instructions, or if you are not sure if
the tool is properly grounded.
SAFETY INSTRUCTIONS
1 • 3-prong plug 2 . Property grounded outlet
3 • Grounding prong
5. USE ONLY THREE-WIRE EXTENSION
CORDS that have 3-prong plugs and 3-prong
outlets that accept the tool’s plug as shown in Fig.
A. Repair or replace a damaged or worn cord
immediately.
\ A CAUTION: l1n all cases, make
certain the power supply outlet in question Is
properly grounded. If you are not sure, have
a licensed electrician check the power
supply outlet.
I A WARNING: ITHIS BENCH DRILL
PRESS IS FOR INDOOR USE ONLY. DO NOT
EXPOSE TO RAIN OR USE IN DAMP
LOCATIONS.
GUIDELINES FOR USING
EXTENSION CORDS
Make sure your extension cord is in good
condition. When using an extension cord, be sure
to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a
drop in line voltage, and result in loss of power
and overheating. The table below shows the
correct size to use according to cord length and
nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number,
the heavier the cord.
Minimum Gauge for Extension Cords (AWG)
Mor.llwl NotMcnThan 25′(7.em) 50′(15m) 100′(30.4m) j 150′(4S.7m)
,. I
,. I
” I ”
Make sure your extension cord is properly
wired and in good condition. Always replace a
damaged extension cord or have it repaired by
a qualified person before using it. Protect y~ur
extension cords from sharp obJects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for you~ tools.
This circuit must not be less than #12 wire and
should be protected with a 15 A time-delayed
fuse. Before connecting the motor to the power
line, make sure the switch is in the OFF
position and the electric current is rated the
same as the current stamped on the motor
nameplate. Running at a low voltage will
damage the motor.
I A, WARNING: !THIS TOOL MUST BE
GROUNDED WHILE IN USE TO PROTECT
THE OPERATOR FROM ELECTRICAL
SHOCK.
Page&
OVERVIEW
T
A Digital speed readout K ·crank handle
B Large ON/OFF switch L Golumh support
C Depth scale M Base
D Chuck N Table lock bolt
E Table 0 Bevel scale
F large, heavy-duty feed handles p Laser line ON/OFF switch
G Housing cover screw H a LED work light switch Housing cover R Support lock handle
I Column
J Rack
s Speed control handle
T Power cord
Page7
SPECIFICATIONS
BENCH DRILL PRESS WITH LASER LINE
MODEL NO.:
MOTOR:
POWER:
SPEED:
SWING:
SPINDLE TAPER:
CHUCK CAPACITY:
QUILL DIAMETER:
STROKE:
CAPACITY:
TABLE TILT:
LASER:
WEIGHT:
RDM1603BNV
120V 60 Hz
550W, 4.6Amp
530-3100RPM
12″ (305mm)
JT3
1/32- 5/8″ (3–16 mm)
2 3/5″ (65 mm)
3 1/8″ (80 mm)
6″ (152 mm) (chuck to column)
19 1/2″ (495 mm) (chuck to base)
O to 45° left and right
Class 111 , transformer powered
77.8 lb (35 kg)
ASSEMBLY AND ADJUSTMENTS
UNPACKING AND CLEANING
Unpack the bench drill press and all its parts, and compare against the list below. Do not discard the
carton or any packaging until the bench drill press is completely assembled.
To protect the bench drill press from moisture, a protective coating has been applied to the machined
surfaces. Remove this coating with a soft cloth moistened with kerosene. Do not use acetone, gasoline,
or lacquer thinner to clean. Apply a coat of paste wax to the table and column. Wipe all parts with a clean,
dry cloth.
K
\or==»» o==»
Cl=- ; ~L
G
Pages
ASSEMBL y AND ADJUSTMENTS
A Head/motor assembly
B Column assembly and table
bracket
C Table
D Base
E Chuck
F Chuck key
G Table lock handle
ASSEMBLY
The column assembly (column, column support,
rack, rack collar, and table support bracket) must
be attached to the base. The table and table
support handles must be attached to the table
support bracket. The motor housing must be
attached to the column.
I A, WARNING: I IF ANY PART IS
MISSING OR DAMAGED, DO NOT PLUG THE
BENCH DRILL PRESS IN UNTIL THE
MISSING OR DAMAGED PART IS REPAIRED
OR REPLACED, AND ASSEMBLY IS
COMPLETE.
Tools needed for assembly
• Adjustable wrench
• Screwdriver
• Hammer and block of wood
Column assembly to base (Fig. 3)
1. Place the column tube (1) on the base (2),
aligning the column support holes to the ·base
holes.
2. Install a hex head bolt (3) in each column
support hole and tighten bolts using the
adjustable wrench.
Paa,9
H Hex head bolts (4)
I Table crank handle
J Hex keys (2)
K Feed and speed handles ( 4)
L LED bulb
M Table adjustment wrench
N Wedge
Table (Fig. 4) · ·
1. Place the cran~ handle (1) onto the shaft
(2) of the tat?le bracket so the flat of the shaft is
under the set screw (8). Tighten the set screw . –
ASSEMBLY AND ADJUSTMENTS
Drill press head to column (Fig. 5)
I A CAUTIOt-,EJ The drill press head is
heavy. To avoid injury, two people should lift
It into position.
1. Carefully lift the drill press head assembly (1)
and position it over the column (2).
2. Place the mounting opening (3) on the drill
press head over the top of the column.
Ensure the drill press head is seated properly on
the column.
3. Align the direction of the drill press head with
the direction of the base and the table.
4. Tighten the set screw (4) using a hex key.
2
Feed handles (Fig. 6)
1. Insert the three feed handles (1) into the
threaded openings on the feed hub (2).
2. Manually tighten handles into openings.
Note: When using the bench drill press, one or
two of the feed handles may be removed if an
unusually-shaped workpiece interferes with
handle rotation.
Speed handle (Fig. 7)
1. Insert the feed handle (1) into the threaded
opening on the speed hub (2).
2. Manually tighten handle into opening.
Mount the bench drill press (Fig. 8)
The bench drill press must be securely fastened
through the mounting holes (1) to a stand or
workbench with heavy-duty fasteners. This will
prevent the bench drill press from tipping over,
sliding, or walking during operation.
IMPORTANT: If the stand or workbench has a
tendency to move during operation, ~asten the
workbench securely to the floor.
LED bulb (Fig. 9)
Insert the LED bulb (1) Into the socket (2) in the
motor head assembly.
Note: LED bulb can be replaced by any 120V SL
LED bulb if the original one runs out of its lifetime.
Install the replacement LED bulb the same way
you install the original one.
Page 10
[AyJARNING: I DISCONNECT THE
BENCH DRILL PRESS FROM THE POWER
SOURCE BEFORE INSTALLING, ADJUSTING,
OR REMOVING THE CHUCK.
To install the chuck (Fig. 10)
1. Inspect and clean the taper hole in the chuck
(1) and the spindle (2). Remove all grease,
coatings, and particles from the chuck and
spindle surfaces with a clean cloth.
2. Open the chuck jaws (3) by manually turning
the chuck barrel clockwise. Make sure the jaws
are completely recessed inside the chuck.
3. Insert the chuck arbor (4) into the oper:iing at
the top of the chuck ( 1 ).
4. Seat the chuck and chuck arbor on the spindle
by placing a block of wood (5; not included) under
the chuck (1) and tapping the wood with a
hammer (6; not included) or tap the .chuck with a
rubber mallet (not included).
! A CAUTION: ; To avoid damaging the
chuck, make sure the jaws are completely
recessed into the chuck. Do not use a metal
hammer to drive the chuck Into the spindle.
1Page11
2
To remove the chuck (Fig.11)
1. Turn the feed handles (1) to lower the chuck
(2) to the lowest position.
2. Place a ball joint separator (3; not included)
above the chuck and tap the separator lightly with
a hammer (4; not included) to cause the
chuck to drop from the spindle.
Note: To avoid possible damage to the drill or
chuck, be prepared to catch the chuck as it falls.
ADJUSTMENTS
To raise or ~ower the table (Fig. 12)
1 . Loosen the support lock handle ( 1) and turn
the crank handle (2) until the table is at the
desired height.
2. Tighten the table lock before drilling.
To rotate the table (Fig. 12)
1. Loosen the support lock handle (1) and turn
the table around the column to the desired
position.
Note: The rack should rotate around the column
with the table support bracket. ff the rack binds
and will not rotate, slightly loosen the set screw
ASSEMBLVANDADJUSTMENTS
in the rack collar.
2. Tighten the support lock before drilling.
To tilt the table (Fig. 13)
1 . Loosen the bevel lock bolt ( 1) with the table
adjustment wrench provided, or with a suitable
socket wrench.
2. Tilt the table to the desired angle, using the
bevel scale (2) as a basic guide.
3. Re-tighten the bevel lock bolt.
4. To return the table to its original horizontal
position, loosen the bevel lock bolt (1).
5. Realign the table to the 0° setting on the
bevel scale (2),
6. Tighten the bevel tock bolt with the wrench.
To Install drill bits (Fig. 14)
1. Place the chuck key (1) into the side keyhole
of the chuck (2), meshing the key with the gear
teeth.
2. Turn the chuck key counter-clockwise to open
the chuck jaws (3).
3. Insert a drill bit (4) into the chuck far enough
to obtain maximum gripping of the chuck jaws.
4. Centre the drill bit in the chuck jaws before
final tightening of the chuck.
5. Tighten the chuck jaws using the chuck key to
ensure that the drill bit will not slip while drilling.
6. Remove the chuck key.
! ,A, WARNING: ! To avoid damaging the
chuck, make sure the jaws are completely
recessed into the chuck. Do not use a metal
hammer to drive the chuck into the spindle.
To square the table to the drill bit (Fig. 15)
1. Insert a 3″ (7.6 cm) long drill bit (1) into the
chuck (2) and tighten the jaws with the chuck key.
2. Raise the table with the crank handle (3)
approximately 1″ (2.5 cm) below the drill bit.
3. Place a combination square (5) on the table
as shown, placing the long straight edge of the
combination square against the drill bit. Make
sure the drill bit is parallel or aligned exactly to the
straight edge of the square.
4. If an adjustment is needed, loosen the bevel
lock bolt (6) with a wrench.
5. Tilt the table slightly, until the combination
straight edge is aligned perfectly with the drill bit.
6. Tighten the bevel lock when square.
Note: Adjustments for the correct function of youc
bench drill press return spring have been done at
the factory. Please do not modify them. However,
prolonged use of the drill press may make some
readjustments necessary.
Page12
ASSEMBL V AND ADJUSTMENTS
Laser line (Fig. 16 and 17)
IAWARNING:l DO NOT STARE
DIRECTLY AT THE LASER BEAM! A HAZARD
MAY EXIST IF YOU DELIBERATELY STARE
INTO THE BEAM, PLEASE OBSERVE ALL
SAFETY RULES: THE LASER SHALL BE
USED AND MAINTAINED IN ACCORDANCE
WITH THE MANUFACTURER’S
INSTRUCTIONS:
• NEVER AIM THE BEAM AT ANY PEBSGN
OR AN OBJECT OTHER THAN THE
WORKPIECE.
• DO NOT PROJECT THE LASER BEAM
INTO THE EYES OF OTHERS.
• ALWAYS ENSURE THE LASER BEAM ·IS
AIMED AT A WORKPIECE THAT DOES NOT
POSSESS REFLECTIVE SURFACES AS THE
LASER BEAM COULD BE PROJECTED INTO
YOUR EYES OR THE EYES OF OTHERS.
1. Place a workpiece on the table.
2. Tum the laser switch (1) to the ON position.
3. Lower the drill bit to meet the workpiece (2).
The two laser lines should cross where the drill
meets the workpiece.
4. If the laser needs to be adjusted:
P.aget3
. a. Using a 3 mm hex key, turn the laser
ad1ustment set screws (~) counter-clockwise.
b. Rot~te t~e laser light housing (4) until the
two la~er Imes intersect where the drill meets the
:no;~:1ece. DO NOT stare directly at the laser
5. Re-tighten the adjustment set screws (3).
Spindle return spring (Fig. 18)
The spindle is equipped with an auto-return
mechanism. The main components are a spring
and a notched housing. The spring was properly
adjusted at the factory and should not be
readjusted unless absolutely necessa1y1.
1. Unplug the drill press.
2. Place a screwdriverr into the loop m \ta hold
the spring in place. . .
3. Loosen me two t;ipusing nuts (2)
approximately
1/4″ (6 mm). Do not remove·the nuts from
the threaded shaft. Do npt allow the spring 3
or spring housing to slip out of control.
4. While firmly holding the spring housing (3),
carefully pull the spring housing out untii it clears
the raised notch (4).
5. Turn the housing so that the next notch (5) is
engaged with the raised notch (4).
• To increase the spindle return tension, turn the
spring housing counter-clockwise.
• To decrease the tension, turn the spring housing
clockwise.
6. Tighten the two housing nuts. Do not
overtighten the two nuts. If the nuts are tightened
too much, the movement of the spindle and feed
handles will become sluggish.
}
Angular “play” of the spindle (Fig. 19)
Move the spindle to the lowest downward position
and hold in place. Try to make the spindle revolve
around its axis while also moving it with a side
motion. If there is too much “play”, proceed as
follows:
1. Loosen·the lock nut (1 ).
2. Without obstructing the upward and
downward motion of the spindle, turn the screw
(2) clock-wise to eliminate the “play”.
Note: A little bit of “play” is normal.
3. Tighten the lock n~t (1).
To replace the belt (Fig. 20)
I A WARNING: I DISCONNECTTHE
BENCH DRILL PRESS FROM THE POWER
SOURCE BEFORE REPLACING THE BELT.
Belt tension and bench drill press speed is
controlled by automatic adjustments made to the
diameter of the front spindle when the drive
handle is moved.
Note: See page 17 for information on the variable
speed function of this bench drill press.
1. Remove the screw that secures the housing
cover (1). Open the housing cover.
~-. Remove the belt (2) from the housing cover if
it is broken. If it is not broken, but is too stretched
to operate correctly, work the belt off the drive
(motor) spindle (3). Then remove the belt from the
front spindle (4).
3. Replace the belt by putting a new belt over
the front spindle (4) and carefully sliding the belt
over the drive (motor) spindle (3).
I A WARNING: i DO NOT CHANGE THE
DRIVE SPEED WHEN THE BENCH DRILL
PRESS IS TURNED OFF.
Page 14
Bench Drill Press ON/OFF switch (Fig. 21)
1. To tum the drill press ON, insert the yellow
safety key (1) into the switch housing (2). As a
safety feature, the switch cannot be turned ON
without the safety key.
2. Flip the switch (3) upwards to the ON position.
3. To turn the drill press OFF, press the switch
downwards.
4. To lock the switch in the OFF position,
remove the safety key (1) from the switch. Store
the safety key in a safe place.
Light and laser Line ON/OFF switches (Fig.
21)
1. The light switch (4) is located below the
ON/OFF switch on the left.
2. The laser switch (5) is located below the
ON/OFF switch on the right.
Page 115
Position the table and workpiece (Fig. 22)
1. Always place a piece of backup material (1)
(wood, plywood, etc.) on the table underneath the
workpiece (2) . This will prevent splintering on the
underside of the workpiece as the drill bit breaks
through.
2. To keep the material from spinning out of
control, it must contact the left side (3) of the
column as illustrated, or be clamped (4; not
included) to the table.
Note: For small workpieces that cannot be
clamped to the table, use a drill press vise (not
included). The vise must be clamped or bolted to
the table to avoid injury.
GENERAL DRILLING GUIDELINES
IAWARNING: I TOPREVENTTHE
WORKPIECE AND THE BACKUP MATERIAL
FROM SLIPPING FROM YOUR HAND WHILE
DRILLING, POSITION WORKPIECE AND
BACKUP MATERIAL TO THE LEFT SIDE OF
THE COLUMN. IF THE WORKPIECE AND THE
BACKUP MATERIAL ARE NOT LONG
ENOUGH TO REACH THE COLUMN, CLAMP
WORKPIECE AND BACKUP MATERIAL TO
THE TABLE. FAILURE TO DO THIS COULD
RESULT IN PERSONAL INJURV.
To drill a hole:
1. Mark where. you want to drill in workpiece by
using a centre· punch or a sharp nail or tum ON
Laser Line to mark drilling point.
2. Before turning ON the bench drill press, tum
the feed handles ·to bring the drill bit down. Line
the drill bit tip up- with the mark. Clal’T!P the
workpiece in place,
3. Turn ON the bench drill press and pull down
on the feed handles with appropriate force
needed to allow the drill bit to drill material.
Note: FEEDING TOO SLOWLY might cause the
drill bit to turn in the chuck. FEEDING TOO
RAPIDLY might stop the motor, cause the belt to
slip, force the workpiece loose, or break the drill
bit. Practice with scrap material to get the feel of
the machine before attempting to do any drilling
operation.
OPERATION
To adjust drilling depth (Fig. 23)
The depth gauge controls the maximum distance
the drill bit will move up or down.
To stop the drill bit at a pre-measured depth:
1. Rotate the upper depth knob (2) until the
bottom of the knob is aligned with the desired
depth mark (5) on the gauge scale.
2. Rotate the depth scale lock knob (1) until it
meets the lower depth scale knob (2). The chuck
will stop after travelling downward to the selected
distance.
To adjust quill (return) height (Fig. 23)
To adjust the upward distance the quill (shaft that
moves up and down) can travel:
1. Turn the feed handles until the quill is at the
desired height and hold it there.
2. Rotate the lower depth knob (3) until it rests
against the bottom of the metal gauge support
(4).
DRILLING BLIND HOLES
Drilling an unmeasured blind hole (not all the way
through the workpiece) to a given depth can be
done two ways: using the depth scale method or
workpiece method.
Depth scale method (Fig. 24)
1. Make sure the o (” or mm) mark on the depth
gauge rests at the top edge of the metal support
(3) when the quill is fully retracted.
2. Put the workpiece on the table, and raise the
table until the tip of the drill bit just touches the top
of the workpiece. Lock the table in place.
3. Determine the drill depth for this workpiece.
4. Rotate the lower depth knob (2) until it is
aligned with the desired depth mark (4) (for
example, 1 “) on the gauge scale.
5. Rotate the upper depth lock knob (1) until it
meets the lower depth knob (2). The chuck will be
stopped at the distance selected on the depth
scale.
Workpiece method (Fig. 24 and 25)
1. Mark the desired depth (5) of the drill hole on
· the side of the workpiece.
2. With the bench drill press in the OFF position,
bring the drill bit (6) down until the tip is even with
the mark.
3. Holding the feed handles at this position,
rotate the lower depth knob (2) until it meets the
metal support.
4. Rotate the upper (1) depth scale lock knob
until it meets the lower knob (2). The chuck and
the drill bit will now be stopped at the distance
selected on the depth scale.
DRILLING SPEEDS
Important factors when determining the best
drilling speed:
• Material type
• Hole size
• Drill bit or cutter type
• Quality desired
Smaller drill bits require greater speed than large
drill bits. Softer materials require greater speed
Page 16
OPERATION
than harder materials . See right speadsheet ‘.0r
recommended speeds tor the workpiece matenal.
Mechanical variable speed (Fig. 26)
This is a variable speed bench drill press. To
increase or decrease the speed when operating,
raise or lower the speed handle ( 1 ).
Use the following table to determine the
recommended speed for the drill size you are
using and the type of material you are to drill.
While drilling, check the speed on the digital
speed readout (2) located at the front of the drill
press.
Recommended Soeed for Dill Size & Material
WOOD
ALUM ZINC
IRON STEEL
SPEED RANDE BRASS
(R.P.M.) in
2000-3100 318 7132 5,6 3132 2.4
1400-2000 518 16.0 11/32 8.75 5132 4,0
1000-1400 22.0 15132 12.0 1/4
800-1000 1-1 /4 31,75 11/16 17,5 3/8
530-800 1-518 3/4 5/8 16.0
MAINTENANCE
[AwARNIN-G: ! FOR YOUR OWN
SAFETY, TURN THE SWITCH OFF AND
REMOVE THE PLUG FROM THE POWER
SUPPLY BEFORE MAINTAINING OR
LUBRICATING THE BENCH DRILL PRESS.
Vacuum sawdust or metal shavings that
accumulates in and on the motor, pulley housing,
table, and work surface.
Apply a light coat of paste wax to the column and
table to help keep these surfaces clean and
Page17
rust-tree.
The ball bearings in the spindle and the V-belt
pulley assembly are greased and pen:nanently
sealed. Pull the spindle _ down anc;t oil the spindle
sleeve moderately every three months.
Lubricate the table bracket and locking knobs if
they become difficult to use.
IACAUTION: !Auservlclngofthedrill
press should be pei:tormed by a qualified
service technician.
PROBLEM
Noisy operation.
The drill bit burns or
smokes.
Excessive drill
run-out
or wobble, drilled
hole
. is not round.
Drill bit binds in the
workpiece.
Spindle returns too
slowly or too quickly.
Chuck falls off
spindle.
TROUBLESHOOTING
PROBABLE CAUSE REMEDY
1. Incorrect belt ten;ion. • Adjust the belt tension. See “To replace
the belt” in ADJUSTMENTS.
2. Dry spindle. • Lubricate the spindle. See MAINTENANCE
section.
3. Loose spindle pulley. • Tighten the retaining nut on the pulley
insert.
4. Loose motor pulley. • Tighten the set screw on the side of the
motor pulley.
1. Drilling at the incorrect • Change the speed. See “Variable speed”
speed. in OPERATION.
2. The wood chips are not • Retract the drill bit frequently to clear the
coming out of the hole. chips.
3. Dull drill bit. • Resharpen or replace the drill bit.
4. Feeding the workpiece • Feed fast enough to cut the workpiece.
too slowly. See “To drill a hole” in OPERATION.
5. Not lubricated. • Lubricate the drill bit with cutting oil or
motor oil.
1. Bent drill bit. • Replace the drill bit.
2. Bit improperly installed in • Reinstall the bit. See “To install drill bits” in
the chuck. ADJUSTMENTS.
3. Worn spindle bearings. • Replace bearings. Take to a qualified
service technician.
4. Lengths of cutting flutes • Resharpen the drill bit correctly or replace
– -or angles not appropriate for with the appropriate type.
‘ the hardness of the wood
grain.
5. Chuck not properly • Reinstall the chuck. See “To install the
installed. chuck” in ASSEMBLY.
1. The workpiece is pinching • Support or clamp the workpiece. See
the bit. “Position the table and workpiece” in
OPERATION.
2. Excessive feed pressure. • Feed more slowly. See “Feeding the drill
bit” in OPERATION.
1. Spring has improper • Adjust the spring tension. See “Spindle
tension. return spring• in ADJUSTMENTS.
1. Dirt, grease, or oil on the • Clean the tapered surface of both the
tapered surface on the chuck and the spindle with a household .
spindle or in the chuck. detergent. See “To install the chuck” in
ASSEMBLY.
Page18
PROBLEM PROBABLE CAUSE REMEDY
1. No backup material under • Always use a backup material. See
The workpiece
“Position the table and workpiece” in
splinters on the the workpiece.
OPERATION.
underside.
The workpiece is 1. Not supported or clamped • Support workpiece using extension wing or
slipping from your properly. clamps. See “Position the table and
hand. workpiece” in OPERATION.
1. Defective or broken • Take to a qualified service technician.
switch. • Take to a qualified service technician.
2. Defective or damaged
power cord.
3. Open circuit, loose • Take to a qualified service technician.
Motor will not run. connections, or burned out
motor.
4. Blown fuse or circuit • Replace fuse or reset circuit breaker. Tum
breaker. off other machines on the same circuit.
5. Low voltage. • Check the power line for the proper
voltage. Use another circuit or have a
qualified electrician upgrade the service.
Motor will not start 1. Short circuit in motor or • Take to a qualified service technician.
and fuses or circuit power cord.
breakers blow. 2. Incorrect fuses or circuit • Replace with correct fuse or circuit breaker
breakers. for the circuit. ·- Motor fails to reach 1. Overloaded circuit. • Tum off other machines and retry.
full power. 2. Improper extension cord. • Replace with proper size extension corc:I.
See ELECTRICAL INFsQ!;IM~Tl(!>N.
1. Short circuit in motor. • Take to a qualifiecl ervice technician. 2. Incorrect fuses or circuit • Replace with correct lase or circuit breaker Motor stalls. breakers. for the circuit.
3. Overloaded circuit. • Turn off other machines and retry. 4. Low voltage.
• Check the power line for the proper
voltage. Use another circuit or have a
qualified electrician upgrade the service.
Page 19
Pa~20
/129
~
Key No. Description Qty Key No. Description
Qty

1 Pan Head Screw, M4x8 2 53 Handle
4 Base 1 54 Hub 3
5 Support clamp 1 55 1 Pin, 5X16
6 Hex socket screw, M8x8 1 56 1 Ring
7 Hex bolt, M16x35 2 57 1 8 Support column Shaft-pinion 1 1 58 Hex bolt, M8x25 4 11 Hex bolt, M10x30 4 59 Washer 11 14 Crank 1 60 Motor 1 15 Hex. socket screw, M6x10 1 61 Key, C4x76 1 16 Worm 1 62 Hex bolt, M8x12 3 17 Gear pin 1 63 Motor mount 1 18 Helical gear 1 64 Pin, 6×16 2 19 Table support 1 65 Screw, M5x12 2 20 Table 1 66 Hex socket screw, M8x8 2 26 Rack 1 67 Hex socket screw, M6x8 4 27 Column tube 1 68 Head 1 28 Hex socket screw, M8x10 2 69 Shaft 2 29 Chuck key 1 70 Shaft plate 1 30 Chuck, JT3 (16mm) 1 71 Pan head screw, M5x10 3 31 Chuck arbor, MT2-JT3 1 73 Cord clamp 3 32 Spindle 1 74 Ball bearing 2 33 Screw, M6x20 1 75 Retaining ring 17 1 34 Ball bearing 1 76 Spacer 1 35 Lock collar 1 n Pulley Insert 1 36 Nut,M6 1 78 Key, 4×60 1 37 Lock nut 2 79 Hex nut, M12 2 38 Quill tube 1 80 Cap-spring 1
39 Lock-depth bolt 1 81 Spring-torsion 4
40 Quill gasket 1 82 Hex nut, MS 2
41 Ball bearing . 1 83 Retaining spring 2
42 Retaining ring 11 1 84 Socket set screw 1
43 Screw, M8x20 1 85 Pan head screw, M5x6 2
44 Lock washer 1 86 Lock washer 2
45 Spring 1 87 Pan head screw, M5x14 3
46 Shaft 1 88 Digital screen 1
47 Laser beam device 2 89 Switch box 1
49 Pan head screw, M3x8 1 90 Switch, HY18 1
50 Lamp assembly 1 91 Light switch, HY35B 2
51 Socket support 1 92 Adjust nut 2
52 Handle knob 4
—4
Page.21
– a
Page23
12″ Drill Press(Variable Speed)
WARRANTY
90-DAY MONEY BACK GUARANTEE
This MASTERFORCETM brand power tool carries our 90-Day Money Back Guarantee. If you
are not completely satisfied with your MASTERFORCE™ brand power tool for any reason
within ninety (90) days from the date of purchase, return the tool with your original receipt to
any MENARDS® retail store, and we will provide you a refund – no questions asked.
3-YEAR LIMITED WARRANTY
This MASTERFORCE™ brand power tool carries our famous No Hassle 3-Year Limited
Warranty to the original purchaser. If, during normal use, this MASTERFORCE™ power tool
breaks or fails due to a defect in material or workmanship within three (3) years from the date
of original purchase, simply bring the tool with the original sales receipt back to your nearest
MENARDS® retail store. At its discretion, MASTERFORCE™ agrees to have the tool or any
defective part(s) repaired or replaced with the same or similar MASTERFORCE™ product or
part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. Not withstanding the foregoing, this limited warranty does not cover
any damage that has resulted from abuse or misuse of the Merchandise. This warranty: (1)
excludes expendable parts including but not limited to blades, brushes, belts, bits, light bulbs,
and/or batteries; (2) shall be void if this tool is used for commercial and/or rental purposes; and
(3) does not cover any losses, injuries to persons/property or costs. This warranty does give
you specific legal rights and you may have other rights, which vary from state to state. Be
careful, tools are dangerous if improperly used or maintained. Seller’s employees are not
qualified to advise you on the use of this merchandise. Any oral representation(s) made will
not be binding on seller or its employees. The rights under this limited warranty are to the
original purchaser of the merchandise and may not be transferred to any subsequent owner.
This limited warranty is in lieu of all warranties, expressed or implied including warranties or
merchantability and fitness for a particular purpose. Seller shall not be liable for any special,
incidental, or consequential damages. The sole exclusive remedy against the seller will be for
the replacement of any defects as provided herein, as long as the seller is willing or able to
replace this product or is willing to refund the purchase price as provided above. For insurance
purposes seller is not allowed to demonstrate any of these power tools for you.
For questions / comments, technical assistance or repair parts –
Please call toll free at: 1-833-498–0653 (M-F 8am – 6pm)
Page24

Leviton plug in lamp dimmer

Download PDF Manual:

Manual Leviton plug in lamp dimmer.pdf

Text of Manual:

Plug-In Lamp Dimmer
Rated: 300W Incandescent, 150W LED & CFL, 120VAC
Cat. No. TBL03 .
DI-OOO-TBL03-22A
INSTALLATION
WARNINGS AND CAUTIONS:
To be installed and/or used in accordance with appropriate electrical codes and regulations.
To avoid overheating and possible damage to other equipment, do not use
exception of compatible d1mmable LED and CFL bulbs. 0 or-opera e or rans armer-supp 19 app iances, with the
DO NOT use with 3-way bulbs. Use with compatible dimmable CFL and dimmable LED bulbs. Please refer to www.leviton.com
compatible bulbs. or a comp e e is
Designed for convenience, reliability and durability
Easy to use slide control
No wiring necessary
6-foot cord for hard-to-get-to receptacles
Smooth dimming of Incandescent, dirnmable LED and CFL bulbs
INSTALLING YOUR DIMMER
1. Plug lamp into dimmer: Turn off lamp. Plug a lamp into the Plug-in Lamp Dimmer (refer to Figure 1 ).
2. Plug dimmer into outlet: Ensure that the Plug-in Lamp Dimmer is in the OFF position (refer to Figure 1). Plug the dimmer into a polarized receptacle.
NOTE: This device i~ a POLARI_ZED cord set. It has a polarized plug (one blade wider than the other) and a polarized outlet (one slot is longer than
the other). The p~larized plug 1s not intended to be mated with non-polarized outlets (having both slots the same size). A polarized outlet is inte,nded to
mate with a polarized plug 1n only one way (the longer slot with the wider blade).
111U=i;t·iii-lO
After installation, turn the lamp in the ON position (the light will remain OFF). To adjust lighting level, proceed as follows:
ON: Raise the slider to the brightness level desired (refer to Figure 2).
OFF: Lower the slider to the OFF position (refer to Figure 2). The light will turn OFF.
NOTE: LED and CFL lamps generally have a higher turn-on voltage requiring the slider to be raised slightly higher until the bulb turns ON.
DIM/BRIGHT: Raise or lower the slider to the desired level.
Dimmer
Gradateur
Atenuador
Figure 1
Slider
Glissiere
Des/izador
..
Figure 2
Deslisador
ENCEND/DO
(brillantez total)
sous tension
(pleine intensite)
Slider ON
(full bright) l Slider OFF
Position hors tension
De.slisador APAGADO
LIMITED 5 YEAR WARRANTY ANO EXCLUSIONS “· · •. . ” . .
Leviton warrants to the original consumer purchaser and not for the benefit of a~yone else that this product at the time of its sale by Levi\on Is free of defects in materials and workmanshlp’llnder normal and
proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at Its option, If within such five year period the product ls returned prepaid, with proof
of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc:, All: Quality Assurance Dep11f1ment, 201 Nortf(‘Servlce Road, Melville, New York 11747. This warranty excludes
and there is disclaimed liability for labor for removal of this product or relnstallatlon. This warranty is void if this product’ Is Installed Improperly or In an Improper environment, overloaded, misused, opened.
abused, or altered in any manner, or Is not used under normal operating conditions or not in accordance with any l11bels or Instructions, There are no other or Implied warranties of any kind, Including
merchantablllty and fitness for a particular purpose, but If any Implied warranty Is required by the applicable jurisdiction, the duration of any such implied warranty, Including m~rchantabllity and fitness for
a particular purpose, is limited to five years. Leviton Is not liable for Incidental, Indirect, spacial, or consequential damages, )ncludlng wlihoUt !Imitation, damage to, or 10111 of use of, any equipment,
lost safes or profits or delay or failure to perform this warranty obllgatlon. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise_::
For Technical Aaslstance Call: 1-800-824-3005 (U.S.’\, Ot11y) www.levlton.com
FOR CANADA ONLY

arranty information and/or product returns, residents of Canada should contact Levllon In writing at Leviton ManUfactur1ng ol Caoada Ltd to the attention of the Quality Assurance Department,
for w Blvd Pointe-Claire (Quebec) Canada H9R 1 E9 or by telephone at 1 BOO 405-5320
© 2012 Leviton Mfg. Co., Inc.
Gradateur enfichable
N° de cat. TBL03
vaIeurs nominales: 300 W (lampes a incandescence), 150 W (DEL et LFC),
120 V c.a.
= INSTALLATION h;t-Ui9¥i
AVERTISSEMENTS ET MISES EN GARDE :
• Installer ou utiliser conformement aux codes de l’electricite en vigueur.
• Pour eviter la surc~autte ou l’endommagement eventuel des appareils
rac~ordes, ne pas tn~taller ce dispositif pour commander un appareil motorise
ou a transformateur, a !’exception de DEL ou de LFC reglables compatibles.
• NE PAS utiliser ce dispositif en presence de lampes a trois voies. II est conc;:u
pour certaines LFC et DEL reglables. Se reporter au www.leviton.com
(en anglais seulement) pour consulter la liste des lampes compatibles.
CARACTERISTIQUES
• Conception assurant commodite, fiabilite et durabilite
• Glissiere facile a utiliser
• Aucun cablage requis
• Cordon de deux metres pour atteindre les prises diffciles d’acces
• Gradation tout en douceur de lampes a incandescence a diodes
electroluminescentes (DE:L) et fluocompactes (LFC) reglables
1. Enficher la lampe dans le gradateur : brancher la fiche d’une tampe
hors tension dans le gradateur (figure 1).
2. Enficher le gradateur dans une sortie : s’assurer que le commutateur
du gradateur est en position hors tension (figure 1) avant de le brancher dans
une prise polarisee.
REMARQUE : le cordon de ce dispositif est dote de connecteurs
POLARISEE. Sa fiche a une lame plus large que l’autre et sa prise a
une fente plus allongee que l’autre. On ne doit pas tenter d’y raccorder des
dispositifs non polarises (ayant des lames ou des fentes de la meme taille). Les
prises et les fiches polarisees ne peuvent etre accouplees que dans un seul
sens, soit en inserant la lame plus large dans la fente plus allongee.
FONCTIONNEMENT
~pres l’installation, mettre la lampe sous tension (elle devrait cependant rester
ETEINTE). Proceder ensuite comme suit pour regler l’eclairage :
MISE SOUS TENSION : hausser la glissiere au niveau d’intensite voulu
(figure 2).
MISE HORS TENSION : abaisser la glissiere jusqu’en bas (figure 2).
REMARQUE : les DEL et les LFC ont generalement
une tension de demarrage plus elevee, exigeant qu’on
hausse un peu plus la glissiere pour les allumer.
TAMISAGE/INTENSIFICATION : deplacer la glissiere vers le haut ou le bas
jusqu’au niveau voulu.
EXCLUSIONS ET GARANTIE LIMITEE DE 5 ANS
Leviton garantit au premier acheteur, et uniquement au credit du dit acheteur, que ce produit ne
presente ni defauts de fabrication ni defauts de materiaux au moment de sa vente par Leviton, et
n’en presentera pas tant qu’il est utilise de fa9on normale et adequate, pendant une periode de 5 ans
suivant la date d’achat. La seule obligation de Leviton sera de corriger les dits defauts en reparant ou
en rempla9ant le produit defectueux si ce dernier est retourne port paye, accompagne d’une preuve
de la date d’achat, avant la fin de la dite periode de 5 ans. a la Manufacture Leviton du Canada
Limitee, au soln du service de !’Assurance Qualite, 165 boul. Hymus, Pointe-Claire, (Quebec),
Canada H9R 1 E9. Par cette garantie, Leviton exclut et decline toule responsabilite envers les frais de
main d’oeuvre encourus pour retirer et reinstaller le produit. Cette garantie sera nulle et non avenue
si le produit est installs incorrectement ou dans un environnement inadequat, s’il a eta surcharge,
incorrectement utilise, ouvert, employe de ta,;on abusive ou modifie de quelle que maniere que ce
soil, ou s’il n’a ete utilise ni dans des conditions normales ni conformement aux directives ou etiquettes
qui l’accompagnent. Aucune autre garantle, explicite ou lmpllclte, y comprls celle de qual_lte
marchande et de conformlte au besoin, n’est donnee, mais si une garantle implicite est requise en
vertu de lois applicables, la dite garantie implicite, y compris la garantie de qualite marchande et de
cor.iformite au besoin, est limitee a une duree de 5 ans. Leviton decline toute responsabillte envers
Jes dommages indirects, partlculiers ou consecutlfs, lncluant, sans restriction, la perte d’usage
d’equlpement, la perte de ventes ou les manques a gagner, et tout dommage-lnteret decoulant du
delal ou du defa~t de l’exe7ution des obligations de cette garantle. Seuls les recours stlpules dans
les presentes, qu 1is s01ent d ordre contractuel, delictuel ou autre, sont offerts en vertu de cette garantle.
– Ligne d’ Assistance Technique : 1 800 405-5320 (Canada seulement)
www.leviton.com
@2012 Leviton Mfg. Co., Inc.
Atenuador Enchufable para Lampara
. No. de Cat. TBL03
Capac,dad: 300W Incandescents, LED & LFC 150W 120VCA
= INSTALACION •¥@M•1′
ADVERTENCIAS Y PRECAUCIONES:
• Para i~stalarse y/o usarse de acuerdo con los c6digos electricos y normas
aprop,adas.
• ~ara evitar sobrecalentamiento y posible daiio a otro equipo, no lo use para
ontrolar artefactos operados por un motor o transformador, con la excepci6n
de focos LED y LFC compatibles atenuables.
• NO lo use con locos de 3 Vias. Uselo con LFC atenuables y focos LED
atenuables compatibles. Por favor, consulte www.leviton.com para una fista.
completa de focos compatibles.
CARACTERISTICAS
• Diseiiado para Conveniencia, seguridad y durabilidad
• Control facil de deslizar
• No necesita cableado
• Cordon de 1.8 m para receptaculos dificiles de alcanzar
• Atenuado suave de focos atenuables LFC y LED, tncandescente
INSTALACION DEL ATENUADOR
1. Conecte la lampara en el atenuador: Apague la lampara. Conecte ta
lampara en el atenuador enchufable (ver Figura 1 ).
2. Conecte el atenuador en el contacto: Asegurese que el atenuador este en
la posici6n de APAGADO (ver Figura 1 ). Conecte el atenuador en el receptaculo
polarizado.
NOTA: Este es un cordon POLARIZADO. Este producto tiene una
clavija polarizada (una cuchilla es mas ancha que la otra) y contactos
polarizados (una ranura es mas larga que la otra). La clavija polarizada esta
fabricada para que no engrane en contactos no polarizados (que tienen ambas
ranuras del mismo tamaiio). El prop6sito del contacto polarizado es que
engrane con la clavija polarizada solo de una manera (la ranura mas larga con
ta cuchilla mas ancha).

Para ‘Aslstencia Teen tea llaine al: 1-800-824-3005 (Soto en EE.UU.)
· www.levlton.com
>40170
DI-OOO-TBL03-ZZA

Kidde fire extinguisher owner’s manual

Download PDF Manual:

Manual Kidde fire extinguisher owner’s manual.pdf

Text of Manual:

Owner’s Manual Manual Del Usuario
Read fire extinguisher labels completely
before you re,1d this owner’s manual.
Lea todas la~ etrquetas en el extingu1dor
antes de leer este manual del usuarlo
Which Extinguisher To Use
fhere ,1re two common types of fire
e1Ct1nguishers Type ABC exl inguishers
fight wood, paper cl nd cloth fires, plus
f/amn1c1ble liquid and electrical flres
Type BC extmgu,shers are for flarnma·
ble hqu1d~ and elect11c~1l fires.
To determine which class or classes of
fire your exl1ngu1sher 1s designed to
fight, loca te the use code symbols on
the front extinguisher label.
Using the wrong extinguisher on a fire
could do more harm than good. Be sure
you understand whicil extinguisher is
appropriate for each class of fire. For
protection against ALL COMMON
CLASSES OF FIRES, you must choose a
type ABC extinguisher.
Inspection And Maintenance
To ensure that your fire extinguisher
will be ready when needed:
• Read and follow all instructions on
label and in owner’s manual.
• Inspect the extinguisher AT LEAST
once a month • more frequently if
exposed to weather or possible
tampering.
• Check that extinguisher is charged.
Pointer on pressure indicator MUST
be in green section. If pointer is in red
or white section..extinguisher is NOT
ready for use.
• Be sure the lock pin is firmly in place.
• Keep the extinguisher clean. Check
for dents, scratches, corrosion or any
other damage.
• Check the discharge noule. Make
sure it is clean and free of obstructions.
Remember the phrase PASS PASS pull the pin aim at the sqUffze SWHp from
base of fire lever & handle side to sJde
Cual Extinguidor Usar
Hay 2 tlpos de extinyuidores. T1po ABC
para usar en ruegos procJucrdos por
maderv, papel y telas, asl como tambr~n
Hquldos 1nflamables v fuegos produodos
par electric/dad rIpo OC para usar
s61o en fuegos produrnJos po , lfquidos
lnflamables y eleclr k idad PiJra detcrrnl·
nar que tipo de eKUngu1dor us led
pos(!c, localice las slmbolos en la elt·
queta frontill. Usar un eKl1nguldor no
dlsenado para una clase de fuego,
puede agravar el incendio AsegUrese
de que comprende cuc1-I extinguidor es
el m~s aproplacJo para cada clase de
fuego. Para una completa protecci6n
CONTRA TODD TIPO DE FUEGD, elija un
extinguldor Tipo ABC.
lnspecci6n y Mantenimiento
Para aseguar que su extinguidor est~ en
buenas condiciones de func ionamiento:
• lea y siga todas las ins trucciones que
aparecen en las etiquetas y el manual
del usuario.
• lnspeccione su extinguidor POR LO
MENDS 1 vez al mes, o m~s a menudo si
se encuentra a la intemperie o existe la
posibilidad de que alguien lo haya
usado.
• Asegure que el extinguidor tenga su
carga. la aguja de/ indicador de presi6n
debe estar en la zona verde. Siesta en
las secciones roja o blanca, su extinguidor
NO ESTA listo para ser usado.
‘° Controle que el gancho de seguridad
1 est~ firmemente ubicado.
• Mantenga el extinguidor limpio.
Verifique que la unidad no tenga abollad_
pras, raspones, 6xido o cualquier otro
da~o.
• lnspeccione la boquilla de descarga.
Oebe estar limpio y libre de cualquier
obstrucci6n.
The fire classifications
(Types of Fire)
A CJ O mrnm ••• The fire extinguisher is filled with a dry chemical
agent. Examine the extinguisher’s instruction
label to determine the types of fire that can be
tackled with this extinguisher.

Wood.

DO NOT TEST BY
PARTIALLY DISCHARGING.
LOSS OF PRESSURE
WILL OCCUR.
Six, Ten or Twelve-Year Limited Warranty
(see below for 1 0 lie 12 year applicable
models).
KIDDE will repair or replace this product
to the original owner free of charge, if
defective in material or workmanship.
This warranty does not apply to damage
resulting from accident, alteration,
abuse or failure to follow Instructions
supplied.
KIDDE, at its option, may refund the
purchase price in lieu of replacement or
repair. ANY AND ALL IMPLIED WARRANTIES,
INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE SHALL BE LIMITED
TO A PERIOD OF SIX (6) YEARS FROM
DATE OF PURCHASE. KIDDE, its dealer,
and distributors shall not be responsible
or in any way liable for any special or
consequential damages for breach of any
warrant or implied warranty.
This warranty gives you specific legal
rights, and you may also have other
rights which vary from state to state.
Ten (10)-Year Warranty applies only
to these models:FX10K, FX110E, FX210R,
FX340SC-2, FX340GW-2. FX340H,
FX340SW, FX34QC. Twelve (12)-Year
Warranty applies onl~ to this
model: FX340SC, XL 2.5 TU-4.
••• NO PRUEBE EL EXTINGUIDOR
DISPAIIANDOLO PARCIALMENTE,
PUES PRODUCIRA UNA
PERDIDA DE PRES/ON.
Seis (6), diez (10), o doce (12) aMs de
garantla limitada (vea abajo modelos de
10 lie 12 alios de garantfa)
KIDDE reparara o repondra este producto
a su dueno original sin costo alguno, si
tiene defecto de materiales o mano de
obra. Esta gar~ntfa no S142re darios causados
por accidentes, alt~o~s. miilfi.Jso a
por no seguir las inStruccion-.,
Como opci6n KIDDE devo,…era el dinero
en vez de repa.raci6n o reemplazo.
TODAS Y CADA UNA DE LAS
GARANTIAS INVOLUCRADAS,
INCLUYENDO CUALQUIER GARANT1A DE
COMERCIABILIDAD O APTITUD PARA UN
PROPOSITO GENERAL DEBERA LIMITARSE
A UN PERIODO DE SEIS (6) ANOS DESDE
LA FECHA DE COMPRA. KIDDE, sus
agentes y distribuidores no serc1n respons•
ables o en ninguna forma culpables por
incumplimiento de cualquier garantfa
escrita o involucrada debido a causas o
dal”ios especiales.
Esta garantla le ofrece derechos legales
especlficos y tambi~n puede tener derechos
adicionales que varlari de estado a
estado. ·
La garantla de dlez (10) ailos solo se
apllca a los modefos: FX10K, FX110E,
FX210R, FX340H, FX340SW, FX340C. La
garantfa de doce (12) ailos solo se aplfca
al modelo: FX340SC.

How To Use Your
Kidde Extinguisher
Follow instructions
shown on the front label
of your f ire extinguisher.
After the fire ,s out, clean up dry chemical
powde, 1mmed1ate ly to avoid corrosion.
CAUTION: Under certa,11 frre and heat
cond1t1ons, the dry chemtCal powder In
ABC type extinguishers will cause damage
or prove extremely difficult to
remove frorn oven surfaces, including
self-cleaning models. Do not use selfcleaning
feature to remove ABC Powder.
BC type extinguishers are recommended
for cooking areas.
CAUTION: The ager1t contained in this
extinguisher is not toxic, but may cause
skin irritation. Avoid inhaling the dry
chemical agent. In case of contact, flush
affected area with clean, cool water. If
irritation persists, contact a physician
immediately. Chemical name of agent is
printed on extinguisher label.
For more information on fire fighting, contact
your local fire department or the U.S.
Coast Guard. Additional information on
extinguishers can be found in the National
Fire Protection Association (NFPA) pamphlet
No. 1 O, ” Portable Fire Extinguishers.”
Mounting Your Extinguisher
Please follow the instructions and diagrams
below for mounting the bracket
that was supplied with your fire extinguisher.
The hanger or bracket provided
with the extinguisher must be used. Use
of an extist ing hanger or bracket may not
properly support or retain the extinguisher.
U.S. Coast Guard approval is valid only
with the marine mounting bracket specified
on the instruction label of your
extinguisher.
Como Usar Su
Extinguidor Kidde
Siga las instrucciones
en la etiqueta del frente
de su extinguidor.
Un.i vez que el luego ha sido ex!lnguldo,
llmple el polvo residual inrnedla tarnenle
para evl tar corrosl6n.
ATENCl6N: Anle cle rtas condlclones de
temper atwa, el polvo ABC contenldo en
este extinguldor (y otras unldades slml\
ares) puede produclr dano y ser muy dillell
de remover en la superficie del homo,
lncluyentlo los que son auto-Urnpiantes.
No use la fun ci6n de au lo-llmpleza para
eliminar el polvo ABC. Extinguidores con
polvo qulmico BC son recomendados en
las areas de codna.
ATENCt6N: Procure no respirar este polvo.
Los ingredientes del mismo no son t6xi~os,
pero pueden producir lrritad6n en la p1eL
En caso de contacto con el mlsmo, lave la
parte afectada con agua frla . Si la
irritad6n persiste, consulte a su ml!dico
inmedlatamente. El nombre del agente
qulmico esttl impreso en la etiqueta.
Para m.is informaci6n sobre el combate
contra incendio, consulte a su Depart·
amento de Bomberos local, o a la Guardia
Castera de las EEUU. lnformaci6n adi·
cional sobre extinguidores contra incendio
puede recabarse en el boletfn #10 de la
Asociaci6n Nacional de Protecci6n contra
\ncendios (NFPA), denominado
“Extinguidores contra fncendio PorMtiles”
Colocaci6n de su Extinguidor
La aprobaci6n de la Marina de las EEUU
es valida s6\o con el soporte especificado
en la etiqueta ubicada en la parte posterior
de su extinguidor. Los Mode\os de
KIDDE (5, 10, 110) estan equipados con
un soporte de plAstico que es aceptado
por la Marina de Los EEUU.
Guardia Castera favor de seguir las
instrucciones y diagramas indicados
abajo para montar el soporte que fue
enviado con su extinguidor. & Plastic wall Metal wall
bracket · hanger hanger
Plastic Strap Bracket Instructions
lnstrucciones del soporte con bandas plasticas en espai’\ol
A 1. Fasten bracket to wall with ..
1 appropriate fasteners (not
Included).
1. Fije el soporte en la pared
con los sujetadores
apropiados (no estAn
incluidos).
IF YOUR EXTINGUISHER WAS SHIPPED
WITH A PLASTIC BRACKET AND METAL
STRAP then mount your extinguisher as
follows:
1. Fasten bracket to suitable
surface using a screw in the upper bracket
mounting hole.
2. Mount the metal strap provided with your
extinguisher in the lower bracket mounting
hole u~ng another screw.
3. Place extinguisher into bracket and latch
the strap to hold the extinguisher securely
in place.
IF YOUR EXTINGUISHER WAS SHIPPED WITH
A HOSE AND HOSE STRAP, then ~ide the
hose strap over the bottom of the cylinder,
and secure the nozzle end of the hose to
the hose strap before placing your extinguisher
in service.
366224R
0 2. Pl~ce extinguisher Into
bracket. Buckle straps
together to lock in place.
~ 2. Coloque el extinguidor en
el soporte. Enganche las
abrazaderas hasta unirse
ensit io.

SI SU EXTINGUIDOR FUE ENVIADO CON
UNA BANDA DE METAL, entonces monte
su extinguidor de la siguiente manera:
1. Ponga el soporte en una superfrcie apmpiada
usando un tomillo de 1/4 de pulgada
en diametro. ponga este en el agujero de
arriba de la montura.
2. Monte la banda de metal que le ha ~do
proveida con su extinguidor en el agujero
de abajo de la montura usando otro
tornillo de 1/4 de pulgada en diametro.
3. Ponga el extinguidor en la montura y
apriete la banda para que aguante el
extinguidor seguro en su lugar.
sf SU EXTINGUIDOR FUE ENVIADO CON
UNA MANGUERA Y UNA ABRAZADERA DE
MANGUERA. entonces, favor de sacar la
abrazadera por la parte de abajo del ciHndro,
ajuste la manguera a la va lvula del
cuerpo y cofoque la punta de la boquil\a de
la manguera a la abrazadera de fa rnrg.ea
antes de poner su extinguidor en se rvicio.
TEAR ALONG PERFORATIONS AND REMOVE

OxGord Scooter for Kids – Deluxe Aluminum 3 Wheel Glider with Kick n Go, Lean 2 Turn, Step 4 Break

Download PDF Manual:

Manual OxGord Scooter for Kids – Kick and Go Scooter – instruction manual.pdf

Text of Manual:

WARNING:
Approved protective equipment (not included) should be worn. 77 Lbs/ 35 Kg MAX. Not to be used in traffic.
Please read instruction manual thoroughly before using the product. Always wear a helmet and protective clothing
when using this product. Do not use the scooter at night or on wet surfaces, uneven or unpaved roadways.
Handle Telescopes
Up To 24″
LEAN & TURN
I l
‘· i
.. ~.=t !WI::-::·\’
Turn Ri.gh-t -~ .’-~~ . , ‘). L
Ow13r&<}f·1:t
‘l • ~’ffi·· > I
i I 111_
.
~
~’l
• ,dfjj ···~- • ti ’11 • I
‘ I Ii
11 I
I!
‘ I i’ j
I ,1 ,l:
Ii I
,.l.::!t
~1/:. -~)I~ Turn Left
~ ~-.. _·.::__, . ,;<~ ‘} ~._r
Kick ‘n Go Scooter requires adult assembly.
• Be sure all parts are assembled securely before riding.
• Please pay attention that the steering column is screwed securely.
CAUTION!
• Not suitable for children under 3 years old.
• Choking hazard. Contains small parts that could be swallowed.
IMPORTANT: Remove the scooter and all parts from the carton. Layout all the
parts and study these assembly instructions before assembling. Save all
packaging material until assembly is completed.
BEFORE ALLOWING CHILD TO RIDE, BE SURE TO READ
Parent’s Responsibility below.
PARENT’S RESPONSIBILITY
• Be sure to read all the instructions carefully and assemble the scooter
according to this Manual before you allow child to ride.
• The scooter requires assembling by qualified adult.
• Special care should be taken to instruct children in safe riding.
• Children should be SUPERVISED while riding the scooter.
• Check the scooter before the child rides to detennine if there are any
POTENTIALLY hazardous parts or conditions.
• Do not allow the child to ride at night.
• Do not allow the scooter to be ridden on streets or areas with auto traffic •
• Do not allow rider to wear anything that obstructs hearing visibility or function.
• Do not allow more than one rider on the scooter at a time .
• Do not allow the scooter to be operated near streets, slopped driveways,
valleys, hills, near small children, in ground pools, areas near steps or any
other hazardous areas.
• Child should always wear a safety standard approved helmet.
• Should always wear a safety standard approved helmet.
• Be sure the rider is wearing appropriate shoes when riding the scooter.
Be sure the rider keeps both hands on the handlebars for proper control.
• Maximum weight 77 Lbs/ 35 Kg.
• The toy shall be used with caution, since it requires great skill to avoid falls or
collisions causing injury to user and third parties.
• Make sure that every locking device is correctly locked.
092016

JTD Key Finder

Download PDF Manual:

Manual JTD Key Finder.pdf

Text of Manual:

Explore The High Definition World
Website:www.jtechdigital .com
Hot Line: 1-888-610-2818[US]
USER MANUAL
KEY FINDER
JTD Second Generation
(4 locators)
JTD-ID-49
Introduction
This remote key finder can help you to find the lost keys, remotes, purse, eyeglass, cane, and other
easily lost items quickly. With just one press on the color-cooed button, the beep sound and flashes
will lead you to find the lost items.
This is an unique remote key finder with LED flashlight. The ON/OFF switch is located at the right side
of the transmitter, which allows you to turn on and off the LED flashlight easily. This becomes extremely
handy wheriyou need to find something.in the dark.
The key finder with base support is also a good display for your tea table, TV bench, bed, computer desk,
bookshelf, etc. The transmitter is removable from base and can be carried with you to find lost items.
Product Diagrams
ON/OFF switch for flashlight
Base
Receivers
Key ring

IO gear USB display port cable KVM switch

Download PDF Manual:

Manual IO gear USB display port cable KVM switch.pdf

Text of Manual:

1 x GCS52DP
1 x Quick Start Guide
1 x Warranty Card
System Requirements
Console:
• DisplayPort monitor
• Standard wired USB keyboard
• Standard 3-button wired USB mouse
• Speakers and Microphones (optional)
Computer:
• DisplayPort port
• USB Type-A port
• Audio ports (optional)
Operating Systems:
• Windows® 2000, Vista, 7, 8.1, 10
• Mac OS X 9.0+
• Oracle® Solaris
• Linux®, UNIX, and other USB supported systems

GranVela iRock

Download PDF Manual:

Manual GranVela iRock

Text of Manual:

IN-LINE CONTROL
Music Playing
• .
:
/
– .-
Play/Pause: While playing music, press the button to pause, and
press again to continue to play.
Switch songs: While playing music, double press the button for tlie
next song and triple press for the last song.
Call Options
Press the button to answer the call.
Press the button to end the call while on the line.
Press the button for 2 or 3 seconds to reject the incoming call.
CORRECT SELECTION OF EARTIPS
04
GranVela
INSTRUCTION MANUAL
AB
Please read the Instruetion before your use and reserve it .
REPLACING EARPIECES/CABLE
Remove the worn-out earpieces, and diagonally place the new
earpieces inside-out, pushing it firmly onto the headphones until it
seats securely around the groove on the shaft; slightly spin the
worn-out cable to remove it, then plug the cord in until it is stable.
EARMUFFS MAINTENANCE
Remove the earpieces from your headphones and wash them by
hand with a mild cleanser mixed with water. After removing dirt,
rinse thoroughly with warm water. Air dry before use.
05
Dear Customer
Thank you for choosing Granvela A8 Earphones. Please read the
user manual c.arefully for proper instruction to maximize the advantage
of the product.A~ Dual Driver In-Ear Headphones, A8 provides unique
sound performance “‘~th well-balanced bass, mids and treble. With
ergonomic Comfort-Fit, it is a perfect companion for you to listen to
music_
CAUTIONS
Please keep or use the headphones at nom1al temperature.
Please do not disassemble, repair or reform the headphones.
Please do not clean the headphones with any chemical solvents.
Please do not throw away or put the headphones in fire.
Please do not expose the headphones to rain or liquid, which may
damage interior components.
Note: High volume may cause hearing loss!
QUALITY WARRANTY . . . ‘
02
The product has one-year warranty and 30-day hassle-free money
back guarantee from the date of purchase.
Any of the below situation is not in the warranty service:
1.The warranty date is expired.
2.Human factors and accidental or deliberate damage is done to
the product. (for example: improper use against the user manual,
improper set up which causes error)
3Any error damage caused by force majeure such as earthquake,
fire, flood etc.
4.Deliberate assembling, repair or refor~ without permission from
our company.
CONTACT US
Website: www.granvela.com
Service Email: Service@granvela.com
Facebook: GranVela Exchange Forum
lntagram: granvela
Welcome to follow us! Please contact us free.
06
Headphones type: In-Ear
Speaker diameter: 14.8mm + 7.4mm
Plug Type: 3.5mm L-bend plug
Transducer Principle: Dynamic
Frequency range: 20-20000 Hz
Impedance: 12 ohm
Sensitivity: 103 dB +/-3 dB
Cable Length: 1.2 m
WARRANTY CARD
Customer Service Data
Name
Telephone
Address
Product Name
Product Type
Purchase Date
Manufacture
Repair Date

Manual for 3M cool flow respirator model 85577 part 2

Download PDF Manual:

Manual for 3M cool flow respirator model 85577 part 2

Manual for 3M cool flow respirator – Package

Text of Manual:

D0-IT-YOURSELF/II0MEOWNER USER INSTRUCTIONS INSTRUCCIONES DE USO HAGALO USTED MISMO/EN EL HOGAR
3NI 8577
Particulate
Re pirator P95
User /11srr11ctirm.,
( IMPORTANT: Keep these
insrr11crio11s.for re.fere11ce)
llespirador Contra
Particulas P95
/11sm1ccio11es de Uso
(JMPORTANTE: G11arde
esras i11sm1ccio11es
para referenciafunira)
n11s resp,ratoc contains no components made
from natural rubber latex.
Este resp1rador no conbene componentes hechos
de IAtex natural.
A.WARNING
This respirator helps
keep non-harmful
dusts and certain particles
out of your nose,
moutll and lungs and
helps ehminate certain annoying
odors. Misuse may adversely affect
your health. For proper use, see
packaging, User Instructions, or call
3M in U.S.A at 1-800-247-3941 .
A ADVERTENCIA
Este respira. dor ayuda a
evitar la entrada de
polvos y ciertas particulas
no daiimos a la nariz,
la boca y los pulmones.
El mal uso puede afectar de manera
adversa la salud. Para uso adecuado
consulte el empaque, las lnstrucciones
de Uso, o name a 3M Mexico al
01-800-71 2-0646.
l’OR MORE. llll’ORMATION
In United States, contact
Internet www.3M.com/occsafety
Technical Assistance: 1-800-243-4630
For other 3M products:
1-800-3M-HELPS or 1-651-737-6501
PARA OBTEHER MAs INFORMACIOff
En Mexico, comuniquese con:
Internet www.3M.com/occsafety
() \lame a 3M en su \oca\idad.
3M Occupational Health and
Environmental Safety Division
3M Center, Building 0235-02-W-70
St. Paul , M 55144-1000
.,. ‘
Read this User /nstroc/Jon Insert beloce
usmg respirator
General lnlonnation
As one of the leading designers and manufacturers
of resp1ra1D<s In the WOfid. 3M provides products
that address the needs of both WO<l<place, regulated
applJCallons and do-rt-yoursett/homeowner, non
regulated applJCatJOOS. For workplace uses, employees
may be exposed to known concentrations
of ham1ful contaminants lor part or all of the wort<day
In these s,tuatJOOS, rasp1rators are intended to
~:=~tt;ta~~~;~~~:;~:t;1;t~~~
hazardous to one that ,s conslderad safe or acceptable
according to government established levels
Employers must also comply with specific regulations
and procedures foc selecting, using, and mamta,
ning proper rasp,ratory protection m the
wort<place that are contained in standards issued by
federal, state oc government agencies such as
OSHA. Do-rt-yoursett/homeowner uses of respirators
are not sim1larty regulated and exposuras are
generally mtenrnttent oc foc short penods of time,
such as weekends In addrtJon, home users cannot
easily detenrnne exposure levels nor do they have
ready access to the type of training, medJCal evaluatJon,
and fit testing needed to be in compliance with
workplace resp,ratoc standards Under these cond1-
11ons, respirators are Intended to help keep nonhannful
dusts and certain other particles out of your
nose, mouth, and lungs and wtth some filters help
eliminate annoying odors only. tt Is Important to understand
that no respira tor will eliminate the Inhalation
of all parbcies nor will It eliminate the J1sk of
disease, Illness, D< death
Government Approval
This 3M resplratoc IS government approved by the
NatJonal lnstrtute foc Occupational Safety & Health
(NIOSH) as an P95 class respiratoc and is designed
for workplace , regulated uses and applications.
Many of these features make thJS product suited foc
do-It yoursett/homeowner and non-regulated applications.
NIOSH certification means the respiratoc
has passed stnngent government pertormance
standards including filtration efficiency testing and
provides at least 95% filtration effJClency against
solid and liquid particles that do not contain oil.
When choosing a respirator foc your home improvement
project or activity, consider looking foc the
NIOSH approval (e.g. N95, P95 or P100) to identify
government-approved products.
This P95 respirator does not supply oxygen and will
not filter gases, vapors D< odors. It is designed to
cover your nose and mouth and will help keep nonhannlul
dusts and certain other particles out of your
nose, mouth and lungs, but will not eliminate the inhalation
of all particles nor will rt eliminate the nsk
of disease, illness or death. It is not mtended foc
use by children nor by individuals with a medical
condrtion that might prevent the use of a rasp1rator,
such as asthma, emphysema oc a history of heart
disease. H you have such a condition, consult your
health care provider before use.
Fitting and Wear Time
To be most effective, this P95 respirator must be
worn at all times when you are exposed to nonhannful
dusts and certain particles. H the respirator
becomes diff1CUlt to breathe throogh oc Is damaged,
immediately go to a non-corrtaminated area and replace
the resplratoc. tt used in environments that
contain oily particles, dispose of respirator after 40
hours of use oc 30 days, whichever is first.
Beards, facial hair oc anything else that prevents direct
contact between the face and the edge of the
respi rator will reduce the effectiveness of this product.
It is also important to understand that using
this respirator will not prevent contaminants from
entering your body throogh other routes such as the
skin, which would require additional personal
protective equipment such as gloves”‘-….tect/
ve clothing.
Inspect the respirator prior to each use and ff any
defect is found, do not use. Check with your local
authorities for proper disposal of used respirators.
3M Mexico S.A. de c.v.
Av. Santa Fe No. 190
Col. Santa Fe, Del. Alvaro Obreg6n
Mtxico D.F. 01210
Use For
Non-hannlul dusts, mists a1ld reduction of ann~~lnQ
odDfS from sotvents ,n petroleum based prodUC h s
which may be encoontered dul1ng activities su~ a.
sanding (bare wood drywall, non-load painted sur
races) oc sweeping projects brushing, rolling Of app1y1ng
certain paints. stains, sealers, cleaners,
finishes petroleum based solvents (e.g tolueneJ
and pai~t strtppers (non-methylene chloride an I t
nonmethanol), using disposable aerosol spray pa~
cans outdoors In well -vent1latt:<1 ~;0s:d~:~
~l l..,j r. l5·-i-J: ~ ,., ,, /fr,{, . .:,,, _
• ., •: _.,. … ••• ·~ … ~ • .\!! ,–.t – —
ply;”:p~~;i:~::~1~:~cts Intended for
~e use ‘using aerosol spray cans, pump bottles,
or garden hose mounted sprays. Pollen and mold .
spores·· and non-ham1ful dusts encountered dunng
outdoor activities such as gardening, cutting fire wood,
raking and mowing. f,Jways use In well-ventl·
lated areas
•tt you scrape, sand, oc remove old paint, you may
release lead dust. Lead Is toxic. Contact the Nallonal
Lead lnformalion Hotline at 1-800-424-LEAD
D< log onto www.epa.gov/lead to find out how to
protect yoursett and your family
“Mold growth can occur quickly indoors when
moisture accumulates in your home as the result of
a flood, plumbing leak, roof leak, etc. Inhaling D<
touching mold spores may lead to allergic reactions
or other health effects in some Individuals. If you
suspect you have an Indoor mold problem in your
home, contact www.epa.gov foc guidance. DependIng
on the extent of the problem, It may be necessary
to hire a qualified mold remediation contractor.
Toe EPA does recommend In “Brief Gulde to Mold,
Moisture, and Your Home” using safety equipment
including an N95 rated respiratoc, safety goggles,
and gloves to help minimize your exposure to mold
rt you attempt to clean-up a small oess than roughly
a 3 ft. by 3 ft.) area yoursett. Consult the EPA foc
additional guidance on how to clean-up small mold
problemsyoursett.
Do Not Use For
My toxic D< hannlul substance such as lead
and asbestos.” “; methylene chloride or
methanol based paint strippers: applying palnL
stains, finishes, weed killer, oc insecticides with
powered sprayers oc equipment: fumigants.
– Many types of building products and insulation
material previously used in homes contained asbestos.
Asbestos is toxic. tt you think asbestos may
be in your home, DO NOT touch or disturb the material
as this may cause asbestos fibers to be released
into the air. Repair or removal of asbestos containing
materials should only be done by a professional
trained in methods foc safely handling asbestos.
Contact the EPA at www.epa.gov foc guidance on
what to do rt you suspect asbestos In your home.
Will Not Work For
Ammonia, bleach odors, fire and combustion
by products such as carbon monoxide, carbon
dioxide, nitrogen oxides, and suttur oxides.
This respirator does not supply oxygen.
Do not use In spaces where there Is not enough
oxygen to support lffe or where a high concentration
of a toxic substance can occur. This could exist In
sealed and confined areas or as a result of activities
oc conditions that may displace oxygen In the space
where you are won<ing. />Jways ventilate the space
you are wort<lng In with fresh air.
The following fitting instructions must be followed
each time the resplratoc is worn:
FITTING INSTRUCTIONS
1. Cup the respirator in your hand, with the nosepiece
at your fingertips, allowing the headbands
to hang freely below your hand. (Fig . 1)
2. Position the respirator under your chin with the
nosepiece up. Pull the top strap over your head
resting It high at the top back of your head. Pull
tho-atnp-you,hoadandpositionlt
around the neck betoW the ears. (Ag. 2)
~hecking the Fri actividad o un prnyec10 de JrelO’as en el hogar hJeS” No usar para
p~o:~/::::1:t~ ~::” have put the resplralor on ~ tiene 1a aixot;!4’. ‘: Nt= ;~ ~~5 ~ ~:~r ~~nc,a f6xica o danma. como p/omo 0 ~:~~~ ~d lnhrne shar~~s tici”t~:e!~~~:i~r! :~: – ~1:: ::ode 1os ocga,ilsmOS gubemamentales ::,1eno o m~:’:1::U.:! ~se cioruro de
r:::~re :1f ~1: ~~1:~~~~:p~:1;;s~i;:~:~~i, ~:::~~~i::;i~~l~,:~~1:~1~:~,,:’i10 ?.i=:T~~;~ ~~~
. oun nose, readJust the nosepiece as de- po1vo no toxJCO y algunas otras partJCUlas fuera de la s pos de productos para construcci6n y
scr~ed In step 3.11 air leaks at the respirator edges nariz la boca Y los pulmones, pero no ehmma la material a,slante antenormente usados en el hogar
WO the straps back along the sides of your head. ‘ mha~li>n de todas las particulas ni ehm1na el J1esQO con~;ian asbesto. El asbesto es toxJCO. SI cree que
Because being able to achieve a
00
• de contraer enfermedades o afeccJOOes o ,oouso la pue haber asbestos en su casa, NO toque o mueva
more of the air you breathe goes !/ii,: f1~ :,ans muerte. No esti destlnado a niiios n, a lndMduos con )lbmatenal, ya que puede provocar la hberac16n de
respirator, we recommend you follow ~Lse problemas de salud que no perm1tan el uso de r~= !sbesto en el a1re. La reparac16n a
steps each time you wear the respirator respiradores, como asma O enfisema, 0 que tengan s6lo d be rtenales que cont1enen asbestos
• antecedentes de cardiopalias. S, usted Ilene alguna de e rea IZarta un protes,onal entrenado en
REMOVAL INSTRUCTIONS
~~~; ~~~:: ~:,t~ and cup resplratoc
strap over head. Still holdin::e:~t:’:~ ‘::a
pull tOI) strap over head and remove respirator. ,
Sho~ld you have any questions on this 3M N95
respirator, call 3M In U.S.A. at 1-soo-247_3941_
IMPORTANTE
Lea estas lnstrucciones para el usuario antes de
ut1llzar el respirador.
lnfurmaclon general
3M, conno uno de los principales disei\adores y fabricantes
de respiradores del mundo, brinda productos
que se aiustan a las necesldades de las aplicaciones
reguladas y en el lugar de traba)o, asl como las de
los proyectos dom~ o del tipo “Mgaio usted
mismo” Y las no reguladas. En el lugar de traba)o, 1os
empleados pueden estar expuestos a concentraciones
conocidas de contamlnantes nocivos durante
la totalidad de la )omada laboral o parte de ella. En
estas situaciones, los respiradores estan destinados
a ayudar .a pro\eger a (\u\enes \os useo, reducieodo
SU exposicl(Jn a los contamlnantes presentes en el
alre de un nivel que pueda ser peligroso a uno que
se considera seguro o aceptable segun los niveles
establecidos por 1os organismos gubemamentales.
Los empleadores tambien deben cumplir con las
reglamentaciones y 1os procedimlentos especificos
para selecciooar, utilizar y mantener una proteccion
respiratona adecuada en el lugar de traba)o, que
aparecen en nonnas emltidas por las agencias
federales, estata1es o gubemamentales conno la AIJministracion
de Seguridad y Salud Ocupacional
(OSHA). B uso de 1os resplradores para aplicaciones
domesticas o del tipo “hagalo usted mismo” no esti
reglamentado del mismo modo y las exposiciones
generalmente son lntennitentes o por breves periodos
de tiempo, por ejemplo 1os fines de semana.
Ademas, 1os usuarios dornesticoS no pueden determlnar
faciknente 1os niveles de exposicl(Jn, ni tienen
estas a1ecoones consulte a su proveedD< de atenci6n ~etodos para maneiar asbestos de manera segura
medJCa antes de’irolizarto. ntacte a la EPA en el sruo www epa gov para
Tiempo de ajuste y uso :=: :’~~que hacer ~ sospecha que hay
Para 1ograr la mayor eficac1a, el respiradof P95 No funcionara para
=t~S::V”c:’ ::i;,~~:~~:~~!st
;i e; Amoniaco; olores de blanqueador, fuego y
toma drticil respirar a traves del res pirador o este se combustmn por productos como mon6xido
dana, dirijase inmedlatamente au~ area no conta- de 1:3rbono, dioxido de carbono, 6x1dos de
minada y reemplacelo. Si se lo ut,hza en amb1entes nitrogeno Y 6xidos de azulre
que contienen particulas aceitosas, deseche el res- Este respirador no sumlnistra oxigeno.
plrador despues de 40 horas de uso o despues de No usar en espacios donde no haya oxigeno suf,-
30 dias, lo que ocurra primero. ~:’~.°u~~n!J..”!~! ~x~ ue’:o~~~~~~~~~r en
La barba, el veHo facial o cualquier otro elemento areas selladas y continadas o como resultado de
que 1mp1da el contacto directo entre el rostro Y el activ1dades o cond1c1ones que pueden desplazar el
borde del respirador reduc1ra la eficac,a de este oxigeno en el espac10 donde est/, trabaJando
producto. Tamb1en es ,mportante comprender que el s,empre vent,le el espac,o en donde esta traba –
uso de este resp1rador no evrtara que las contam1· jando con aire fresco
nantes ingresen al cuerpo por otras vias, ~~a la
ptel, lo que requenria un equipo de proteccK>n per- Oebe respetar las s,guientes mstrucciones de oolosonal
adicional como guantes u otra vest,menta de cacion cada vez que use el resp1rador
proteccilin.
1nspeccione el respirador antes de cada uso y,
si detecta algun defecto, no lo Ulllice. Consulte a
las autoridades locales para saber c6mo ehminar
adecuadamente los respiradores usados
Usar para
Polvos no daninos, neblinas y reduccl6n de olores
moiestos de solventes en productos base petroleo
que pueden estar presentes en activ,dades como lijado
(madera desnuda, yeso, superficies con pmrura
sin plorno”) o proyectos de banido, cep1llado, o aplicacion
de ciertas pmturas, tmtes, selladores,
limpiadores, acabados solventes base petrtileo (por
e.g. tolueno) y removedores de pmrura (cloruro ~n
metileno y metanoQ: con latas de pmtura en aerosol
desechables en espacios ab1ertos con buena venblacion:
aplicaci6n granular, con polvo, o herb1c1das
liquidos, o productos para el control de insectos,
hormigas, araiias o cucarachas para uso en el
hogar con latas en aerosol, rociadores o aerosoles
montados en mangueras para el Jardin. Polen yesporas
de moho” y polvos no danmos presentes en
actividades en el exterior, como jardineria, corte de
madera, banido de hoJas y corte de pasto.’ Siempre
u:;e en 61″8M con bucnd vcnti/m;fOft.
“Si raspa, lija o quita pinrura vieja, tal vez libere
polvo con plomo, el cual es t6xico. Contacte a la
Linea Nacional de lnformaci6n sobre Plomo al 1-
800-424-LEAD o visite el sitio www.epa.govnead
para saber ci>mo protegerse.
INSTRUCCIONES DE AJUSTE
1. Ponga el resp,radoc sobre su mano de manera
que cubra con el clip nasal las puntas de sus
dedos, permillendo que las bandas cue\c;iuefl 1\bremente
baJO su mano. (Fig. 1)
2. Ponga el resp1rador baJo su barbilla con el clip
nasal hac,a amba Tome la banda superior y
pci:sela sobre su cabeza para colocarta atras, en
la parte supenor de la cabeza Pase la banda inferior
sobre su cabeza y coloquela alrededor del
cuello, bajo las ore1as. (Flg 2)
3. Coloque las puntas de los dedos de ambas
manos sobre el clip nasal Usando los dedos de
ambas manos, moldee el ci1p para adaptal1o a la
fonna de su nanz empu1ando hac,a adentro al
m,smo tiempo que mueve las puntas de los
dedos hacia abaJO por ambos lados del clip nasal.
(Fig.3)
Revision de ajuste
un acceso lnmedlato al tipo de capacitaclon,
evaluacion medlca y pruebas de a)uste que se
necesitan para cumplir con las normas para
respiradores en el lugar de trabajo. En estas
condiciones, los resplradores estan destinados
solamente a ayudar a mantener el polvo no toxico y
algunas otras particulas luera de la nariz, la boca y
1os pulmones, y a ayudar a ellminar algunos olores
molestosconcieltosfiltros.Esiflll)Oltanlecornpreoclef
que ning(Jn respirador elimlnara la inhalacli>n de
todaslasparticulasnieliminanielriesgodecontraer
enfennedades o afecciones o lncluso la muerte.
-EJ crecimlento de moho puede ocunir rapidamente
en interiores cuando la humedad se acumula como
resultado de inundaciones, lugas en las caiierias,
goteras en 1os techos, etc. lnhalar o tocar esporas de
moho puede ocasionar reacciones aiefgicas u otros
efectos a la salud en algunas personas. s, sospecha
que tiene moho en el interior en su hogar, visite el
Para ayudar a detenn,nar s, ha colocado el rasp,rador
correctamente, cofoque ambas manos
cubriendo compJetamenle el resp1rador e ,nha/e con
1\leflll…l”tt,go t;U’!UoOO ‘ltt.oo~ “”-~’«:In Qt\
respirador al haceno. Se debe sentir una presilin
negativa dentro del respirador. Si sale aire alrededor
de la nariz, reajuste el clip nasal como se descnbe
en el paso 3. SI sale aire por los bordes del resplrador,
reajuste las bandas jalando hacia atras a
ambos \ados de la cabeza
Debido a que lograr un buen ajuste signttica
que mas del aire que resplra pase a traves del
respirador, \e recomendamos que siga estos
pasos cada vez que lo use.
Aprobaclfin gubemanartal
Este resl)iradorde3M hasiloaprobado porel lnstitUto
Naciona1 de Seguridad y Sa1ud Ocupaciooa1 (NOSH)
CD<OOresl)iradordaseP95yhasilodisefiadopara :::car::::~
INSTRUCCIONES PARA
QUITARSE EL RESPIRAOOR
Vea el paso 1 de las /ns/TUCC/0/18S de aJusle Y sujete
el raspiradO< con la mano para mantener la
posici6n en la cara. Pase la banda infenor sabre la
cabeza Mantenga la poslcioo del res(llradD<, pase_
\a banlla sul)el10! ‘SOl>lt “”tal>tta ~ <>.•~el,~-
3. Place your fingertips from both hands at the top
of the metal nosepiece. Using two hands, mold
the nose area to the shape of your nose by pushing
inward while moving your fingertips down
both sides of the noseplece. (Ag. 3)
producto adecuado para ap1lcaciones domesticaS y de(
tipo “Mgaio usted mismo” y no reguladas. La certifi..
caclon de! NtOSH slgniflca que este producto cumple
con estriclas normas gubemamentales de
rendlmiento, entre ellas la prueba de eficacia de filtrado,
yque ofrace una eficacla de filtrado de por io
rnenos un 95% para particulas sillidas y liquidas que
contienen aceite. CUando ellja un respirador para una
sitio www.epa.gov como guia Segun la magnitud del
prob1ema, puede ser necesario contraw a 111a persona
ca1ificada que se encargue de( moho. La Agencia de
Proteccion Amblental (EPA por sus slglas en ingles)
recormenda en “Brief Guide to Mold, Moistura, and
Your Horne’ (‘ Gula breve para el tratamiento del
moho_ y la humedad en el hogar”), usar equlpo de
seguridad, como resplradof N95, goggles y guantes
de segurldad para minim\zar la exposlcion al rnoho si
intenta llmplar un area pequei\a (que mida menos de
3 pies por 3 pies). Coosulte la EPA para obtener guia
adicional en c6mo limpiar problemas pequei\os de
moho usted mismo.
rador.
s, tiene alguna duda acerta del respirador P95 3M
name a JM MexJCO al 01 -800-712-0646.
©3M 2008 34-8700-8936-3

Air Fort

Download PDF Manual:

Manual Air Fort

Text of Manual:

DB
AIR FORT
USER
ANUAL
~ WARNING
Read all warnings and instructions before
assembling this inflatable device and keep
instructions for future use.
AGES
3 to 14 years
1
~WARNING
Read all warnings and instructions before
assembling this inflatable device and keep
instructions for future use.
Failure to follow the installation and operating
instructions presents a risk of serious injury or
death.
• FOR INDOOR HOUSEHOLD USE ONLY
on a flat and level floor surface.
• Adult supervision is required at all times.
Adult supervision should be either from
inside the Air Fort or outside at the viewing
window.
• Age range of users: 3 to 14 years ·
• Maximum number of users: 3 to 5
• DO NOT use this product or locate the fan
or power cord near water, open flames,
potential falling objects or in indoor areas
where vehicles frequent, such as garages.
• DO NOT place or throw objects of any
kind on this product at any time.
• DO NOT run in or around this product.
• DO NOT inflate or use within 4 feet of any
objects.
.• DO NOT jump on this product.
1










Keep the bottom edge all around the Air
Fort free from obstruction at all times.
DO NOT allow rough play such as running
or somersaults.
DO NOT attach any items to this product,
such as, but not limited to, jump ropes,
clotheslines, pet leashes, cables or chains,
as they have the potential to cause
strangulation.
DO NOT consume food or drink inside this
product.
DO NOT allow users to wear clothing with
hard, sharp, or dangerous components.
DO NOT allow users to play with sharp
objects in or around this product.
DO NOT allow pets in or on the Air Fort.
In case of a power outage or sudden
deflation of the Air Fort, exit the Air Fort.
DO NOT use until Air Fort is re-inflated.
If Air Fort becomes torn or damaged,
discontinue use of the product and contact
us.
Use ONLY a GFCI protected electrical
outlet to plug the fan electrical cord
into.
2
• Use ONLY a 20″ household box fan or
18″ tabletop round fan that is certified
by a recognized electrical testing
laboratory, is child resistant and stable, .
and has an electrical cord that is
protected.
• ALWAYS secure this product to the fan
per the instructions.
• DO NOT use a gasoline powered fan
or blower to inflate this product.
• DO NOT use an extension cord with
the fan.
• DO NOT allow any part of the electrical
cord to be inside the inflated product.
• DO NOT allow foreign matter to be
blown into the air tunnel.
• DO NOT allow children near the fan. ·
NOTE: Remove all packaging materials prior
to use. DO NOT allow children to play with
packaging. The storage bag is NOT a toy. DO
NOT allow children to play with it.
3
Parts list
1-Air Fort inflatable
4-1″ looped adhesive squares with backing
1-drawstring storage bag
1-instruction manual
Assembly and inflation instructions
1.Completely open and lay out the Air Fort as
shown in Figure 1, with warning label facing
up, in the location where it will be used,
observing all the warnings above regarding
this location.
Figure 1
4
2.Stretch out the fan shroud and read the
warnings on the fan shroud.
3.Make sure the fan is. NOT plugged into an
electrical outlet.
4.Locate the four 1″ looped squares with
adhesive backin as shown in Figure 2.
Figure 2
Refer to the applicable instructions in the
following pages for the type of fan used
· for inflati.on.
5
l
l
For assembly using a 20-inch Box Fan
1.Remove backing from the adhesive on each
looped square and place them on the four corners
of the fan as shown in Figures 3a and 3b.
Figure 3a Figure 3b
2.Attach the two white straps to the two looped
squares on the top corners of the fan as shown jn
Figure 4.
Figure 4
6
3.Attach the two black straps to the two looped
squares on the bottom corners of the fan as
shown in Figure 5.
Figure 5
For assembly using an 18-inch tabletop Round
Fan
1.Remove backing from the adhesive on each
looped square and place them on both sides of
the fan in the locations shown in Figures 6a and
6b.
Figure 6a Figure 6b
7
2.Attach the two white straps to the two
looped squares on the sides of the fan motor
housing as shown in Figures ?a and 7b.
Figure 7a Figure 7b
3.Attach the two black straps to the looped
squares on the sides of the fan base as
shown in Figure 8.
Figure 8
8
Inflation
1.Plug fan into an electrical outlet.
2. Turn the fan on to any setting to inflate. Your
Air Fort will inflate faster on the highest setting.
3.Fan must remain on for your Air Fort to stay
inflated.
4.lnflation may take up to 30 se·conds depending
on the type of fan and the speed setting.
5.Once inflated, you may be able to lower the fan
speed setting to maintain inflation.
6.To enter and exit your Air Fort, lift bottom edge
anywhere around the product. The Air Fort will
temporarily deflate, but will re- inflate once the
edge is returned to the floor as shown in Figure 9.
Figure 9 .
9
Deflation and disassembly
When finished using your Air Fort have all
occupants exit the fort. ONLY THEN turn off the
fan and unplug it from the electrical outlet.
Remove the four straps from the fan and store
your Air Fort in the provided drawstring storage
bag.
Maintenance and Care
Proper maintenance of the Air Fort will ensure the
safety of the users as well as longevity of the
product.
~ en not in use, store the Air Fort in the provided
drawstring storage bag and keep in a cool, dry
place.
To clean: wipe with warm water and a soft cloth. If
use of soap is needed, use a non-flammable, nontoxic
cleaning and sanitizing solution such as
Simple Green All-Purpose Industrial Cleaner®.
10
DR
AIR FORT
“Have fun in the best AIR FORT you have ever
built!”
airfort.com
~
AIR FORT
USER
MANUAL
. Lh WARNING
Read all warnings and instructions before
assembling this inflatable device and keep
instructions for future use.
AGES
3 to 14 years

Lunchbox Nordic by Nature

Download PDF Manual:

Lunchbox Nordic by Nature

Text of Manual:

Better insulation: Made with thicker 4mm neoprene, your Nordic
by Nature lunch bag keeps your lunchbox nicely chilled for up to
4-6 hours.
R.oom for Medium Lunches: This stretchy tote fits even your bulkier
lunch box containers. Wider bottom keeps bag upright;
heavy-duty zipper keeps it secure; colorful interior keeps it stylish!
No More Soggy Food: Why pack your water bottle in with your lunch,
where it can 11 sweat11 & soak your sandwich? Instead, stash it in our
separate neoprene sleeve, where it’ll stay cold & convenient.
Non-Toxic 6 PVC-Free: Relax! Your lunch bag & bottle sleeve are
100% safe, for you and for the environment. Plus, both are
washable, reusable & foldable for easy storage.
60-Day Guarantee: We’re sure you’ll love your Nordic by Nature
Set: lunch bag & bottle sleeve. But, if you don’t, just return it
within 60 days of delivery for a full money-back refund.
instructions: We recommend you wash before initial use.
Dishwasher-safe, simply drape the bag over the tines. Turn inside
out if very dirty. Like an old pair of jeans, the bags will soften and
fade with repeated wash.
NORDIC BY
NATURE
#NordicByNaturelunchBag