Target lanterns MODEL NO205-278 ITEM# 746739-102

Download PDF Manual:

Target lanterns MODEL NO205-278 ITEM# 746739-102

Full Text of Manual:

 

2.Enclosed Parts
Metal frame with cap; 10 pcs
raDric lantern; 10 pcs
10LT string: 1 pc
S.Assembly
^EsSaJte Figure 1.
1. Warning. Risk of fire, personal injury, and electric shock
Instruction
4) Plua linhfcof ■ *me 3 ^ame as shown in Figure 4

^■Troubleshooting:
If lights do not work
MODEL NO:205-278
ITEM# 746739-102
® 2017 Target Tb, Ms9ye Design is , ^ of Targei
LANTERN
Figure 4
PRINTED IN CHINA
Ail Rights Reserved.
USER SERVICING INSTRUCTIONS . To replace the fuse:
a) Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on
top of attachment plug towards blades.
c) Remove fuse carefully. Turn plug over to remove fuse.
d) RISK OF FIRE. Replace fuse only with 3 Amp,
125 Volt fuse provided with product.
e) Close fuse cover. Slide closed the fuse access cover
on top of attachment plug.
f) RISK OF FIRE. Do not replace attachment plug.
Contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is
damaged.
To replace a lamp:
a) Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
b) Pull lamp and plastic base straight out of lampholder.
c) Replace lamp with only 3.6 Volt, 0.072 Watt, LED type
lamp (provided with product).
If the new lamp base does not fit in lamp holder, follow the steps below before step 3.
1 .Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
2.Thread leads of new lamp through holes in old base with one lead in each hole.
3-After lamp is fully inserted into base,bend each lead up,like other lamps in the light
set so that the leads will touch the contacts inside the lamp holder.
CAUTION: a) Risk of fire. This product does not contain lamp shunts, which
allow the product to operate if one lamp burns out. Replace lamps only with the spare
lamps provided with this product.
b) Replace lamps only with 3.6 volts, 0.072 watt spare LED lamps provided with this product.
Connecting Sets End to End:
CAUTION .This string is rated 2.4 Watts (0.02Amps), do not overload. Connect
other Lighting Strings or decorative outfits end-to-end up to a maximum of 216 Watts
(1 .SAmps) total. If connecting to a lighting string that does not have a wattage (W)
rating (found on the tag within 6 inches of the plug), Calculate the wattage (W) as follows:
Multiply the current (A) which is on the flag type label located within 6 inches of the plug,
by 120. For example, string is rated 120V, 60Hz, 0,02Amps, 0.02 x120=2.4 Watts.
Add the wattage of each light string together for a total of 216 Watts or less.
(Do not exceed 216 Watts.) FOR INDOOR AND OUTDOOR USE.
CUSTOMER SERVICE INFORMATION: If you have questions about this product or its use,
refer to our web site at www.seasonalspecialties.com
for FAQ’s or call 1-855-995-6598 Monday through Friday 9:00 AM to 5:00 PM CST
SSC NO: 746739-102 – Z2528 -17
MODEL NO. 205-278 E309873,101 Rev C 100325 Printed in China
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
a, READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the product
to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a
qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplace, candles or other
similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and
electric shock it should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m) This product is equipped with push-in type LED lamps. Do not twist lamps.
n) This product employs overload protection (fuse). A blown fuse indicates an overload
or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also
unplug any additional strings or products that may be attached to the product. Replace
the fuse as per the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a short-circuit may be
present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided with the product.
P) SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS a) When the product is placed on a live tree, the tree should be well maintained and fresh.
Do not place on live trees in which the needles are brown or break off easily. Keep the
tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut,
damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures,
loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed,
including trees, branches, or bushes, to avoid any undue strain or stress on the product
conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
f) The LED lamp has polarity. Do not deliberately change the direction of the LED lamp
in the lampholder.

Leave a Reply