![\"\"](\"http:\/\/www.twistidea.com\/manual\/wp-content\/uploads\/sites\/3\/2018\/11\/Manual-Schwinn-SW76193-4-Brake-and-Derailleur-Cable-Repair-Set.png\")
<\/p>\n
Full Text of Manual:<\/p>\n
SCHWINN\u00ae
\nBike Cable Ki~ Instructions
\nModel #: SW76193-4
\nParts: \u00b7th SIS
\n1. Two 2 double ended ge~r) cables w1 rear
\n. (Index compatible) housing – 1 fro~t, ~ using
\n2. Two double ended brake cables with o
\n3. Eight ferrules
\n4_ Four cable end caps
\nTools
\n1 Bike stand or assistant
\n2. Look at nut and bolts on your brakes.
\n\u00b7 W hes may be: 4mm or 5mm hex wrench \/
\nrenc 6″ d. \u00b7t bl h Bmm, 9mm, 1 Qmm box wrench \/ a JUS, a e wrenc
\n3. Sharp diagonal pliers or cable cutter
\n4. Awl or ice pick
\n5. “Third hand” brake tool or an assistant
\n6. White lithium grease
\nGear Cable Installation . .
\nNote: Both front and rear derailleur use springs and cable
\ntension. The spring moves the derailleur as the cable tension
\nis deceased.
\nThe cable moves the derailleur in the opposite direction as
\ncable tension is increased. There are usually two limit screws
\nthat stop the derailleur form moving to far either direction.
\n1. Before loosening any gear cables, turn handle bars as until they
\nare close to the top tube. If the cables are tight you will need to
\nincrease the length of the housing.
\n2. Move shift levers until both front and rear derailleur cables \u00b7are
\nnot under tension.
\n3. Loosen cables (gear wires) on both front and rear
\nderailleurs (shifters).
\n4. Remove gear cab\/es. The short..ene is-the front cable.
\nThe longer one is the rear derailleur cable.
\n5. Match the cable heads. Then cut off the non-matching head.
\n6. Lay the able housing on a flat surface and lay the new housing
\nnext to it. If the cables were tight when the handle bars were
\nturned in step # 1 hold cable to bike and add length.
\n7. Use an awl or ice pick to open cable housing ends.
\n8. Route gear housing like originals.
\n9. Add ferrules per originals.
\n10. \u00b7Lightly grease cable (gear wires) and insert them in housing.
\n11. Pull cable to cable anchor bolt. Make sure derailleurs are in
\nmost relaxed position. Tighten cables.
\n12. Front derailleur – either suspend the bike or have a friend hold
\nthe rear wheel up. Turn the pedals and move the front shift
\nlever. Front derailleurs can be either shift small to big chain
\nwheel or big to small chain wheels. Watch the cage on the front
\nchain wheels. Either way the limit screws determine how far the
\ncage will move. Push on the cage to determine which way it
\nmoves. It will move in that direction when’tension is applied to
\nthe cable.
\nRear derailteur – with bike still suspended or rear wheel held up
\nmove rear shift lever to relaxed position. The chain should be \u00b7
\non the smallest outside cog. If it is on next inner cog, loosen
\nlimit screw with wheel turning until chain moves on to
\nsmallest cog.
\n13. With the pedals turning move both shift levers one at time.
\nThe chain must not fall off the small or big chain wheels. The
\nchain must not bypass the biggest rear cog and go into the
\nspokes or fall off the smallest outer cog. There may be some
\nminor chain rub when the chain is in maximum cross-ave~ .
\nposition. The best solution is to select another gear combination.
\n14. The cable should be tight enough not to dip. There will be
\nhousing compression. The cable tension will need to be
\nadjusted several times.
\n15. Use cable cutters or diagonal pliers to trim excess gear c~ble.
\nLeave 1 \u00bd” of extra cable. Crimp on cable end cap with pilers.
\nSCHWINN\u00ae
\nBike Cable Kit Instructions .
\nModel #: SW76193-4 continued …
\nFront and Rear brakes
\n1. Before loosening any brake cables, turn handle bars as until
\nthey are close to the top tube. If the cables are tight you will
\nneed to increase the length of the housing.
\n2. Brakes use springs to open and cables (brake wires) to close.
\n3. Loosen cables (brake Wires) on both front and rear
\nbrakes (shifters).
\n4. Remove brake cables. The short one is the front cable. The
\nlonger one is the rear derailleur cable.
\n5. Match the cable heads. Then cut off the non-matching head.
\n6. Lay the cable housing on a flat surface and lay the new housing
\nnext to it. If the cables were tight when the handle bars were
\nturned in step #1 hold cable to bike and add length.
\n7. Use an Awl or ice pick to open cable housing ends.
\n8. Route brake housing like originals.
\n9. Add ferrules per originals.
\n1 o. Lightly grease cable (brake wires) and insert them in housing.
\n11. Pull cable to cable anchor bolt. Make sure brakes are in most
\nrelaxed position. Squeeze brake calipers to make sure they
\nopen easily.
\n12. Squeeze brake arms until brake shoes touch rims. Use third
\nhand brake tool or have your assistant hold brake arms.
\n13. Tighten cable at anchor bolt.
\n14. Squeeze brake lever. The brake shoes should be close but not
\ntouch the rim. Re-adjust cable as necessary.
\n15. Cable housing will compress under normal use. Check brake
\nadjustment often.
\n16. Make sure the brake shoes do not rub on tire.
\n17. Use cable cutters or diagonal pliers to trim excess brake cable.
\nLeave 1 \u00bd- of extra cable. Crimp on cable end cap with pliers.<\/p>\n","protected":false},"excerpt":{"rendered":"
Download PDF Manual: Manual Schwinn SW76193-4 Brake and Derailleur Cable Repair Set.pdf Full Text of Manual: SCHWINN\u00ae Bike Cable Ki~ Instructions Model #: SW76193-4 Parts: \u00b7th SIS 1. Two 2 double ended ge~r) cables w1 rear . (Index compatible) housing – 1 fro~t, ~ using 2. Two double ended brake cables with o 3. Eight … Continue reading “Schwinn SW76193-4 Brake and Derailleur Cable Repair Set”<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[2],"tags":[],"class_list":["post-102","post","type-post","status-publish","format-standard","hentry","category-user-manual"],"_links":{"self":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/102","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/comments?post=102"}],"version-history":[{"count":1,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/102\/revisions"}],"predecessor-version":[{"id":105,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/102\/revisions\/105"}],"wp:attachment":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/media?parent=102"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/categories?post=102"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/tags?post=102"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}