![\"\"](\"http:\/\/www.twistidea.com\/manual\/wp-content\/uploads\/sites\/3\/2018\/12\/KT-LCD3-e-Bike-Display-User-Manual-v3.0.png\")
<\/p>\n
Full Text of Manual:<\/p>\n
KT-LCD3 e-Bike Display User Manual V3.0
\nDear customer, please read this manual before you use KT-LCD3 instrument. The manual will guide
\nyou use the instrument correctly to achieve a variety of vehicle control and vehicle status displays.
\nFunctions and Display
\nInstruments using the structure form of instrument body portion and the operation buttons are
\ndesigned separately.
\n1 a UP button 10 A 6KM\/H push power assist
\n2 m SW button KM\/H Riding speed(metric)
\n3 Q DOWN button
\n11
\nMPH Riding speed (imperial)
\n4 Battery capacity indicator MXS MAX speed
\n5 = \u00bb Backlight and headlights AVS Average speed
\n6 o The brake display Km Distance(metric)
\n7 TM Single trip time Mil Distance (imperial)
\nTIM Total trip time 12 DST Trip distance
\nMOTOR W Power display ODO Total distance
\n8 MOTOR \u00b0C Motor temperature VOL Battery voltage
\nMOTOR T Motor Fahrenheit
\n13
\nASSIST Pas level
\n9 V Environment temperature CRUISE Cruise function
\nT Environment Fahrenheit
\nOperation
\n1. ON\/OFF
\nHold \u25a0 button long to turn on the power, and hold SHU button long for a second time to turn
\noff the power. When the motor stops driving and when the e-bike is not used for a consecutive 5
\nminutes, it will automatically shut down and turn off the motor power supply.
\n2. Display 1
\ni sco^os;;
\nnGG.\u00a3 : \u00aes?
\nu 5232 S
\nHold button to start up and enter display 1.
\n2.1 Turn on backlight and headlights
\nBHold JSl button long to turn on backlight and headlights (the
\ncontroller should have headlight drive output function); hold a button
\n……………………….. i long again to turn off the backlight and headlights.
\n2.2 Assist ratio gear (ASSIST) switch
\n\u25a0.—– .: . . s Hold O or O button shortly to switch 1-5 file gear. Gear 1 is for
\nSthe minimum power, gear 5 is for the highest power. Each startup will
\n!T i automatically restore the gear shutdown last time (the user can \u25a0”…………… -…. i randomly). Gear 0 is without booster function.
\n2.3 6KM\/H assist promotion function
\nHold S button and flashes, the vehicle drives at the speed not
\nmore than 6Km \/h. Release a button, the function is invalid.
\n2.4 Crui i
\nAfter the cruise function is turned on, the trip riding speed is greater
\nthan 7 km\/ h, hold a button long and enter cruise, the CRUISE lit. Brake
\nor hold any button to cancel.
\n2.5 Display and delete of single data
\nAfter power on for 5 seconds, hold Cl and B button at the
\nsame time, single trip riding time (TM) and single trip distance (DST) flash,
\nhold MB button shortly, the content of both is cleared. If failed holding
\nthe button within 5 seconds, it will automatically return the display interface after 5 seconds, original
\ncontent is preserved.
\n3. Display 2
\nUU2 23
\n“33B3.8…-SS
\n\u25a03S Suu DD –
\nn 00.\u00b0 53
\nu 03CC3 Hold button shortly in display 1 to enter display 2.
\nIn the riding mode after 5 seconds, display 2 automatically returns to display 1, and the original
\nmotor power (MOTOR W) display is replaced with motor operating temperature display (MOTOR \u00b0C)
\ndisplay (the internal motor should be equipped with the temperature sensor and the output of
\ntemperature detection signal).
\n4. Displays
\nME \u25a0 GBB’DC\u2122
\nu i3S8′ <33,
\nHold button shortly in display 2 to enter display 3.
\n7.1 Error Code Display
\nIn the riding condition, five seconds later, a single maximum speed (MXS) display automatically
\nreturns to the real riding speed (KM\/H).
\n5. In display 3, hold IS! button shortly (SW),and the display will re-enter display 1.
\n6. Hold IKS’ button to turn off the display and the power supply of controller.
\n7. Automatically prompt interface
\nDefinition
\nThrottle Abnormality
\nMotor hall signal Abnormality
\nTorque sensor signal Abnormality
\n05 _info Axis speed sensor Abnormality(only applied to torque
\nsensor)
\n06 _info Motor or controller has short circuit Abnormality
\nElectronic control system failure will display (flashing) fault code. Once the fault was removed, it
\nautomatically exits from the fault code display interface.
\n7.2 Motor temperature alarm
\nWhen the motor temperature (the internal motor should be equipped with the temperature sensor
\nand the output of temperature detection signal) is over the warning value, MOTOR \u201dC (T) flashes to
\nalarm at any display, meanwhile the motor controller will offer the appropriate protection to motor.
\nGeneral Project Setting
\n1. Set maximum riding speed i
\n2V
\nError Code
\n01_Jnfo
\n03_Jnfo
\n04_Jnfo
\n05___jnfo
\n06_Jnfo
\nAfter power on for 5 seconds, hold (lasS and mmi button at the
\nsame time, maximum riding speed KM\/H and MXS flash, hold IS or
\nI w button shortly to set the maximum riding speed (default 25KM\/H).
\nHold IISM! button shortly and go to the next parameter settings.
\n2. Wheel diameter setting
\nThe wheel diameter will be set after finishihg setting the maximum riding speed, wheel diameter
\nspecifications flashes. Hold m or S’ button shortly to set the specifications of wheel diameter.
\n\u00a34,n
\n3. Set the metric units
\nSelect the range 6,8,10,12,14,16,18,20,22,24,26,700c and 28 inches. Hold
\nbutton shortly and go to the next parameter settings.
\nThe metric units will be set after finishing setting wheel diameter,
\nKM\/H and Km flash. Hold 191 or a button shortly and select the
\nthree metric units of speed, mileage, and ambient temperature in
\nsynchronization.
\nDisplay Metric Imperial
\nRiding speed KM\/H MPH
\nTotal distance Km Mil
\nEnvironment temperature \u201dC Temperature T Fahrenheit
\n4. KM\/H and Km stop flash after metric unit setting is completed. Hold iKM button shortly again to
\nre-enter the maximum riding speed setting interface; or hold Ififi! button long to exit from setting
\nenvironment of routine projects and save the setting values, returning to display 1.
\n5. Exit from routine project setting
\nAll three routine project settings can exit from the setting environment and return to the display
\nif hold IB) button long after each setting is completed, meanwhile the setting values are saved.
\nUnder each setting interface, if the button failed holding for more than 1 minute, it will
\nautomatically return to display 1, and the setting value is invalid.
\nOutline Drawings and Dimensions
\n1. Dimensions of main instrument body 2. Mounting dimensions of double brackets<\/p>\n","protected":false},"excerpt":{"rendered":"
Download PDF Manual: KT-LCD3 e-Bike Display User Manual v3.0.pdf Full Text of Manual: KT-LCD3 e-Bike Display User Manual V3.0 Dear customer, please read this manual before you use KT-LCD3 instrument. The manual will guide you use the instrument correctly to achieve a variety of vehicle control and vehicle status displays. Functions and Display Instruments using … Continue reading “KT-LCD3 e-Bike Display User Manual v3.0”<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[2],"tags":[],"class_list":["post-177","post","type-post","status-publish","format-standard","hentry","category-user-manual"],"_links":{"self":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/177","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/comments?post=177"}],"version-history":[{"count":1,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/177\/revisions"}],"predecessor-version":[{"id":180,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/posts\/177\/revisions\/180"}],"wp:attachment":[{"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/media?parent=177"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/categories?post=177"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.twistidea.com\/manual\/wp-json\/wp\/v2\/tags?post=177"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}