Full Text Searchable PDF User Manual
OWNER'S MANUAL
Split Air Conditioner
Thank you for choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
air conditioner for correct operation, please
CAIR
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
ner for correct operation, please
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
nditioner for correct operation, please
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
ir conditioner for correct operation, please
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
air conditioner for correct operation, please
AIR
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
air conditioner for correct operation, please
PICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
g
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
oosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
or choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
you for choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
Thank you for choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
Thank you for choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
OWNER'S MANUAL
Split Air Conditioner
Thank you for choosing
air conditioner for correct operation, please
ALPICAIR
it carefully for consultation.
read this owner's manual carefully before operating the unit and keeps
For air conditioners:
AWI/AWO-53HPR1 Delta
AWI/AWO-65HPR1 Delta
Split Air Conditioner
Installation manual
Thank you for choosing our air conditioner, please read this
owner's manual carefully before operating the unit and keep
it carefully for consultation
2
1.
2.
4.
5.
6.
7.
8.
1.
3.
1.
2.
3.
●
●
●
●
●
●
10
.
11
.
The appliance shall not be installed in the laundry.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a hazard.
The temperature of refrigerant circuit will be high, please keep the interconnection cable
away from the copper tube.
9
.
Installation service- Notices for installation
Important Notices
The unit installation work must be done by qualified personnel according to the local
rules and this manual.
Before installating, please contact with local authorized maintenance center, if unit is
not installed by the authorized maintenance center, the malfunction may not solved,
due to discommodious contacts.
When removing the unit to the other place, please firstly contact with the authorized
BVT
Maintenance Center in the local area.
Basic Requirements For Installation Position
Install in the following place may cause malfunction. If it is unavoidable contact with
service center please:
Place where strong heat sources, vapors, flammable gas or volatile objuct are emitted
.
Place where high-frequency waves are generated by radio equipment, welders and
medical equipment.
Place where a lot of salinities such as coast exists.
Place where the oil (machine oil) is contained in the air.
Place where a sulfured gas such as the hot spring zones is generated.
Other place with special circumstance.
Indoor Unit Installation Position Selection
The air inlet and outlet vent should be far from the obstruction, make sure that the air
can be blown through the whole room.
Select a position where the condensing water can be easily drained out, and the place
is easily connected for outdoor unit.
Select a location where the children can not reach.
Can select the place where is strong enough to withstand the full weight and vibration of
the unit. And will not increase the noise.
Be sure to leave enough space to allow access for routine maintenance. The height of the
installed location should be 250cm or more from the floor.
Select a place about 1m or more away from TVset or any other electric appliances.
Select a place where the filter can be easily taken out.
Make sure that the indoor unit installation should accord with installation dimension
diagram requirements.
Outdoor Unit Installation Position Selection
Select a location from which noise and outflow air emitted by unit will not inconvenience
neighbors, animals, plants.
4
.
A air switch having a contact separation of at least 3mm in all poles should be fixed in
fixed wiring.
5
.
The appliance shall be installed in accordance with national wiring regulation.
1 2
.
Avoid a location where there is heat source high humidity or inflammable gas.
13
.
Do not use the unit in the immediate surroundings of a laundry a bath a shower or a swi-
mming pool.
3
1.
2.
3
.
4
5
.
●
●
Air conditioner is type electric appliance, thus please do conduct reliable earthing
measure.
The yellow-green
two-color
wire
in
air
conditioner is earthing wire and cannot be used
for other propose. It cannot be cut off and be fix it by screw, otherwise it would cause
electric shock.
The user power must offer the reliable earthing terminal. Please don't connect the
earthing wire with the following place:
①
Tap water pipe
.
②
Gas pipe
.
③
Contamination pipe
.
④
Other places that professional personnel consider them unreliable.
Note:
It should be reliably earthed, and it should be connected to the special earth device,
the installation work should be
operated by the professional.
The air switch must have the functions of magnetic tripping and heat tripping,
in order
to protect the short circuit and
overloading.
.
The min. distance from the unit and combustive surface is 1.5m.
wrong connection may cause fire.
The power supply should be used the rated voltage and AC exclusive circuit,the power
cable diameter should be satisfied.
1
.
3
.
2
.
Voltage applying range: the normal running range is rated voltage 90%-110%.
Don't drag the power cable emphatically.
Safety Requirements For Electric Appliances
Notices for installation
6.
7
.
8
.
9
.
Make sure that the outdoor unit installation dimension should accord with installation
dimension diagram, convenient for maintenance, repair.
The height difference of connecting the tubing within 5m, the length of connecting the
tubing within 10m.
Select a place where it is out of reach for the children.
Select a place where will not block the passage and do not influence the city appearance.
4.
5.
The location should be able to withstand the full weight and vibration of the outdoor unit
and permit safe installation.
Select a dry place, but do not expose under the direct sunlight or strong wind.
2.
3.
Select a location where there should be sufficient ventilation.
Select a location where there should be no obstructions cover the inlet and outlet vent.
In case necessary, please consult your supply authority for system impedance information.
18K can be connected only to a supply with system impedance no more than 0.211 ohm.
●
In case necessary, please consult your supply authority for system impedance information.
24K can be connected only to a supply with system impedance no more than 0.466 ohm.
●
Make sure that the Live wire or Zero line as well as the earth wire in the family power
socket can not be wrong connected, there should be reliable and no short circuit in the
diagram.
Ⅰ
Earthing requirements
Space to the obstruction
Air inlet side
Space to the wall
Air outlet side
Space to the wall
ev
ob
A
Above
A
B
4
Installation dimension diagram
Space to the ceiling
Space to the wall
Space to the floor
Air outlet side
Space to the wall
The dimensions of the space necessary for
correct installation of the appliance
including the minimum permissible
distances to adjacent structures.
A
B
378
(mm)
342
(mm)
5
5
0(mm)
572
(mm)
The outdoor unit installation
dimension
Models
18K
24K
I
nstallation dimension diagram
Above
Above
Above
Above
Above
Above
Above
Above
5
φ65mm
φ65mm
Violet
Orange
Fig.7
Fig. 8
Terminal board
Blue
Black
Yellow-
green
Wire terminal
cover plate
Cord anchorage
Cord anchorage
Violet
Brown
Orange
Terminal board
Blue
Black
Yellow-
green
Fig.
6
65
AWI-53HPR1/AWO-53HPR1
Ø
1. Always mount the rear panel horizontally. As the water drainage pipe at the left, when
adjusting the rear panel, this side should not be too high; the right side should be slightly high.
2. Fix the rear panel on the selected
location.
3. Be sure that the rear panel has
been fixed firmly enough to withstand
the weight of an adult of 60kg,
furthermore, the weight should be
evenly shared by each screw.
Mark on the middle of it
Gradienter
Wall
Wall
Space to
the wall
150mm
above
Space to
the wall
150mm
above
Left
Right
(Rear piping hole) (Rear piping hole)
1
.
Make the piping hole
(
65
)
in the wall at a slight downward
slant to the outdoor side. At Fig.6.
2
.
Insert the piping-hole sleeve into the hole to prevent the connection
piping and wiring from being damaged when passing through the hole.
Indoor Outdoor
Wall pipe
Seal pad
Protection
sleeve pipe
Install the water drainage pipe
1
.
For well draining, the drain hose should be
placed at a downward slant.
Do not wrench or bend the drain hose or flood its end by water.
2
.
3
.
When the long drainage hose passing through
indoor, should wrap the insulation materials.
Wrenched Bent
Flooded
Connect indoor and outdoor electric wires
1
.
Open the front panel upwardly;
2
.
Screw off the fixing screw of cover plate
and screw off cover
plate (As show in Fig. 7)
3
.
Put the power connection cable through the
back of indoor unit wire hole and take it out.
4
.
Connect the power connection cable to the
terminal block.(As shown in Fig. 8)
5
.
Fix the power connection cable the sheath
with cord anchorage.
6
.
Cover the front panel cover.
Install indoor unit
Ø
Install the rear panel
Install the piping hole
AWI-65HPR1/AWO-65HPR1
6
●
●
●
●
●
●
1.
⑴
⑵
2.
3.
4.
1
.
2
.
Ф6
Ф9.52
Ф
12
31~35
15~20
50~55
Install indoor unit
NOTE:
When connecting the electric wire if the wire length is not enough, please contact with
the authorized service shop to buy a exclusive electric wire that is long enough and the
joint on the wire are not allowed.
The electric wiring must be correctly connected, wrong connection may cause spare
parts malfunction.
Tighten the terminal screw in order to prevent loose.
After tighten the screw, slightly pull the wire and confirm whether is it firm or not.
If the earth wire is wrong connection, that may cause electric shock.
The cover plate must be fixed, and tighten the connection wire, if it is poor installed, that
the dust, moisture may enter in or the connection terminal will be affected by outside force,
and will cause fire or elelctric shock.
Install the indoor unit
The piping can be lead out from right, right rear,
left, left rear.
When routing the piping and wiring from the left
or right side of indoor unit, cut off the tailings
from the chassis in necessary (show in Fig.
9
).
Cut off the tailings 1 when routing the wiring only;
Cut off the tailings 1 and tailings 2 when routing
both the wiring and piping.
Take out the piping from body case, wrap the piping
electric wire, water pipe with tape and put them th-
rough the piping hole (As show in Fig.1
0
)
Hang the mounting slots of the indoor unit on the
upper tabs of the rear panel and check if it is firm
enough. (As show in Fig.1
1
)
The height of the installed location should be 2
.5
m
or more from the floor.
Install the connection pipe
Align the center of the piping flare with the
relevant valve.
Screw in the flare nut by hand and then tighten
the nut
with spanner and torque wrench refer
to the following.
Tightening torque table
Hex nut diameter
Tightening torque table(N.m)
NOTE: Firstly connect the connection pipe to indoor unit, then to outdoor unit; pay attention
to the piping bending, do not damage the connection pipe; the joint nut couldn't tighten too
much, otherwise it may cause leakage.
Tailing 2
Tailing 1
Fig.
9
Fig.
10
Fig.
11
Right
Right nether
Right rear
Left
Left rear
Mounting
board
Mounting
board
Fixing hook
Gas side piping
External connection
electric wire
Liquid side
piping
Gas side piping
Finally wrap it
with tape
Water drainage pipe
Liquid side
piping
insulation
Indoor unit piping
Taper nut
Piping
Torque wrench
Spanner
insulation
Ф
16
6
0~
65
3.
4.
5.
●
●
1.
2.
Electric wiring
Disassemble the handle on the outdoor unit right
side plate.
Take off cord anchorage. Connect and fix power connect
cord (for cooling and heating unit,connect and fix power
connect cord and signal control wire)to terminal board.
Fix the power connection cable with cord anchorage.
Ensure wire has been fixed well.
Install the handle.
NOTE:
Wrong wiring may cause spare parts malfunction.
After the cable fixed, make sure there should be a free space between the connection
and connection and fixing place on the lead wire.
2.
3.
4.
1.
Remove the front side plate.
Take off cord anchorage. Connect and fix power connect cord to
terminal board.
Fix the power connection cable with cord anchorage
Ensure wire has been fixed well.
5
.
Install the front side plate.
For AWI-65HPR1/AWO-65HPR1:
For AWI-53HPR1/AWO-53HPR1:
AWI-53HPR1/AWO-53HPR1
Orange
Blue
Black
Violet
Yellow-green
Connection diagram of indoor unit and outdoor unit:
wire
Blue
Indoor unit terminal board
Yellow-green
Black
Violet
Orange
Power
conne-
ction
Outdoor unit terminal board
Violet
Brown
Blue
Black
Orange
Yellow-green
Front side plate
Connection diagram of indoor unit and outdoor unit:
Yellow-green
Indoor unit terminal board
Outdoor unit terminal board
wire
Blue
Black
Brown
Violet
Orange
Power
conne-
ction
7
Install outdoor unit
Cord anchorage
Cord anchorage
AWI-53HPR1/AWO-53HPR1
AWI-65HPR1/AWO-65HPR1
8
Install outdoor unit
A i r p u r g i n g a n d l e a k a g e t e s t
1.
Take out the nut cover of the inlet for refrigerant.
2.
Align the center of the piping and tighten the conical nut with hands.
3.
To tighten the conical nut with spanner.
4.
Take off the valve cover of liquid valve and gas valve and nut of Freon charge nuzzle.
5.
Loosen the valve stem of liquid valve with a hex wrench. Push the check valve core of
gas valve to discharge air and moisture remaining in refrigerant system.
6.
After 15seconds, stop pushing the valve core as soon as the
refrigerant starts to be discharged, and reinstall the service port nut.
7.
Open the stem of liquid valve and gas valve completely. (As show in Fig. 12)
8.
Tighten the valve cover, use the soap water or leakage detector to test,
the outdoor unit and pipeline connection leak or not.
9.
If possible, adopt vacuum pump vacuum the air from the gas stem.
(As show in Fig.13)
Outdoor condensation drainage (Heat pump type only )
When the unit is heating, the condensing water
and defrosting water can be drained out reliably
Installation: Install the outdoor drain elbow in 25
hole on the base plate,and joint the drain hose to the
elbow, so that the waste water formed in the outdoor
Ø
Valve cap
gauge
Vacuum pump
Liquid pipe
Gas pipe
Fig.13
Fig.12
Chassis
Outdoor drain elbow
through the drain hose.
Gas pipe
Liquid pipe
Liquid valve
Hexagon
Gas valve
Freon charge nuzzle
Screwdriver
unit can be drained out to a proper plate.
Vacuum
9
1.
(1)
(2)
(3)
(4)
2.
(1)
(2)
Check after installation and test operation
Check after installation
Items to be checked
Possible malfunction
Has it been fixed firmly?
The unit may drop, shake or emit noise.
Have you done the refrigerant leakage test?
It may cause insufficient cooling(heating)
capacity.
Is heat insulation sufficient?
It may cause condensation and dripping.
Is water drainage well?
It may cause condensation and dripping.
Is the voltage in accordance with the rated
voltage marked on the nameplate?
It may cause electric malfunction
or damage the part.
Is the electric wiring and piping
connection installed correctly and securely?
It may cause electric malfunction
or damage the part.
Has the unit been connected to a secure
earth connection?
It may cause electrical leakage.
Is the power cord specified?
It may cause electric malfunction
or damage the part
.
Is the inlet and outlet been covered?
It may cause insufficient cooling(heating)
capacity.
Has the length of connection pipes
and refrigerant capacity been recorded?
The refrigerant capacity is not accurate.
Test Operation
Before test operation
Do not switch on power before installation isfinished completely.
Electric wiring must be connected correctly and securely.
Cut-off valves of the connection pipes should be opened.
All the impurities such as scraps and thrums must be cleared from the unit.
Test operation method
Switch on power, press "ON/OFF" button on the wireless remote control to start the operation.
Press MODE button, to select the COOL, HEAT, FAN to check whether the operation is
normal or not.
10
Fig. a
Installation Instructions
1. Forcibly pull the panel for a specific angle
from the two ends of the front panel according
to the arrow direction. Then pull the air filter
2. Mount the healthy filter onto the air filter,(as
shown in Fig.b). If the air filter cannot be in-
stalled, please mount the healthy filter on
3. Mount the air filter properly along the arrow
direction in Fig.d, and then close the panel cover.
ion filter can't be cleaned with water, while active carbon, photocatalyst,
low temperature conversion (LTC) catalyst, formaldehyde eliminator, ca-
The healthy filter commonly has its usage lifetime for one year under
normal condition. As for silver ion filter, it is invalid when its surface becomes
according to the installation instruction. Pay special attention to that silver
Take out the healthy filter before cleaning and reinstall it after cleaning
Installation and Maintenance of Healthy Filter
●
Healthy filter
Air filter
Healthy filter
downwards to remove it. (See Fig.a)
the front case. (as shown in Fig.c).
Fig. b
Fig. c
Fig. d
techin or mite killing filter can, but can't with brush or hard things. Dry it in
the shade or sun after cleaning, but not by wiping.
black (green).
goods, the latter one shall prevail. The quantity of healthy filters shall be
based on the actual delivery.
This supplementary instruction is provided for reference to the unit with
healthy filter. If the graphics provided herein is different from the physical
Cleaning and Maintenance
Service Life