Full Text Searchable PDF User Manual
EPLT
EPTL
OWNER´S MANUAL
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
Thanks you very much for purchasing our air conditioner.
Please read this owner´s manual carefully before using
your air conditioner.
2
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
HANDLING THE REMOTE CONTROL
REMOTE CONTROL SPECIFICATION
FEATURES OF REMOTE CONTROL BUTTONS
INDICATORS ON DISPLAY PANEL
AUTO OPERATION
COOL / HEAT / FAN OPERATION
DRY OPERATION
TIMER OPERATION
EXAMPLE OF TIMER SETTING
SLEEP BUTTON FUNCTION
RESET AND LOCK BUTTONS FUNCTION
DIRECTION/SWING BUTTON FUNCTION
CAUTIONS
CONTENTS
3
4
9
5
10
7
10
14
8
12
14
14
15
CAUTIONS
Keep running condition your air conditioning performing at least every six months clean
the filters, coils and fans.
Keep in good working control systems, such as the thermostat.
The comfort temperature is between 21° C and 23° C, holding the temperature within
this range will help the team save more energy.
Do not place the thermostat near spotlights, lamps or heat-producing appliances and
the operation of the system may be inadequate and / or poor.
When using the air conditioner keep doors and windows closed in conditioned
environments in order to keep out hot outside air.
If the area where the air conditioner is going to remain idle, shut down your computer
for saving energy.
In unconditioned spaces should reduce the heat load introduced by excessive lighting or
equipment remain on unnecessarily.
3
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
8 mts.
26.25 ft
The air conditioner will not operate if curtains, doors or the materials block the signal
from the remote control to the indoor unit.
Prevent any liquid from failing into the remote control. Do not expose the remote control
to direct sunlight or heat.
If the infrared signal receiver on the indoor units is exposed to direct sunlight, the air
conditioner may not function properly. Use curtains to prevent the sunlight from failing
on the receiver.
If other electrical appliances react to the remote control, either move these appliances or
consult your local dealer.
CAUTIONS
HANDLING THE REMOTE CONTROL
Keep the remote control where the signal can be received by the indoor sensor unit
(maximum of 8 meters.)
When you use the time schedule, the remote control automatically transmits the
signal to the indoor unit.
If that does not work, check the batteries.
4
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
REMOTE CONTROL SPECIFICATIONS
MODELO
R51/4BGE, R51/4BGCE, R51/19/BGE,
RG1/19BGCE
Rated Voltage
3.0V (Dry batteries LR03 X 2)
Lowest Voltage of CPU Emitting Signal
2.0V
Signal Receiving Range
8m (26.25 ft)
Environment
-5º C (23º F) ~ 60º C (140º F).
1
1
2
2
3
3
4
Operating Mode: AUTO, COOL, DRY, HEAT (Cooling only model without) and FAN.
Timer Setting Function in 24 hours.
Indoor Setting Temperature Range 17º C ~ 30º C.
Full function of LCD (liquid Crystal Display).
The remote control uses two alkaline dry
batteries (R03/LR03X2)
Slide the cover of the battery
compartment off according to the arrow
direction, and then replace the old
batteries with new ones.
Insert the new batteries making sure that
the (+) and (-) of battery are installed
correctly.
Reattach the cover by sliding it back into
position.
Do not use old batteries or different type batteries, otherwise it may cause the remote
control malfunction.
REPLACING BATTERIES
PERFORMANCE FEATURE
NOTE
5
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
FEATURES OF REMOTE CONTROL BUTTONS
1
2
3
TEMP Button : Push this button to decrease the indoor temperature setting.
TEMP Button : Push this button to increase the indoor temperature setting.
MODE Selection Button: Each time the button is pressed, the operation mode is
shifted in the direction of the arrow.
FIG. 1
10
11
12
13
14
15
16
FOLLOW
ME
SELF
CLEAN
ADJUST
CLEAN AIR
8
6
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
6
7
8
9
10
11
4
5
Heat mode is for cooling & heating models only.
DIRECTION/SWING Button: Press this button once and quickly to change the air
flow direction of the horizontal louver a little. The moving angle of the louver is 6º
for each press. Press the button without releasing for 2 more seconds, the horizontal
louver would swing automatically. Press it again, it would stop moving. When the
louver swing/moving at a certain position which would automatically change the
swing diretion (upward or down).
CLEAN AIR Button (on Some models): When push this button, the Ionizer or
Plasma Dust Collector (depending on models) is energized and will help to remove
pollen and impurities from the air.
SELF CLEAN (AUTO CLEAN) Button: Press this button under COOL or DRY mode,
the self clean function is activated. Press it again will stop the operation and turn
off the unit.
FOLLOW ME Button (on some models): Push this button to initiate the Folow
Me, the remote control will send thisa signal to the air conditioner every 3 minutes
interval until press the folow me button again. The air conditioner will beep to
indicate the Folow Me feature has ended if it does not receive the signal during any
7 minutes interval.
RESET Button: When you press the recessed RESET button, all current settings are
cancelled and the control will return to the initial settings.
ON/OFF Button: Press this button to start the indoor unit. Press again to stop the unit.
FAN SPEED Button: Press the button to select the Fan Speed in the sequence:
AUTO, LOW, MED and HIGH. Each time the button is pressed, the fan speed selection
is shifted.
TIMER ON Button: Press this button to initiate the auto-on time sequence. Each
press will increase the auto-timed setting in 30 minutes increments. When the
setting time displays 10 h, each press will increase the auto-timed setting 60
minutes increments. To cancel the auto-timed program, simply adjust the auto-on
time to 0.0.
SLEEP Button: Press this button to go into the Energy-Saving operation mode.
Press it again to cancel. This function is only can be used on COOL, HEAT and AUTO
mode and maintain the most comfortable temperature for you.
12
While the unit is running under SLEEP mode, it would be cancelled if ON/OFF, FAN SPEED,
SLEEP or MODE button is pressed
NOTE
NOTE
7
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
1
2
3
14
15
16
13
TIMER OFF Button: Press this button to initiate the auto-off time sequence. Each
press will increase the auto-timed setting in 30 minutes increments. When the
setting time displays 10 h, each press will increase the auto-timed setting 60 minutes
increments. To cancel the auto-timed program, simply adjust the auto-off time to
0.0.
LOCK Button: Press this recessed button to lock all current setting, and the remote
control will not accept any operation except that of the LOCK, use the LOCK mode
when you want to prevent settings from being changed accidentally. Press the LOCK
button again to cancel the LOCK function, A lock symbol will appear on the remote
control display when the lock function is activated.
TURBO Button: Push this button to activated the Turbo function wich enables the
unit to reach the present temperature in the shortest time. When press this button
on cooling mode, the unit will blow strong cooling air with super high fan speed,
When press this button on heating mode (applicable to the unit adopts PTC only),
the PTC wil be energizer and bring fast heating operation.
INDICATOR ON DISPLAY PANEL
MODE DISPLAY: Display the current selected mode. Including AUTO, COOL, DRY,
HEAT (Cooling & Heating models only) and FAN.
TRANSMISSION Indicator: This transmission indicator will light when remote control
transmits signals to the indoor unit.
TEMP. / TIMER DISPLAY Indicator: The temperature setting (from 17ºC to 30ºC)
or timer setting (0-24h) will be displayed. If FAN mode is selected, there will be no
display.
LED DISPLAY Button: Press this button to clean the display the indoor unit, press it
again to light the display.
The unit system will automatically revert back to the prevoius setting after continue
operating under powerful cooling mode for about half an hour.
Buttons design might be sligthly different from the actual one you purchased depending
on individual models.
All the functions described are accomplshed by the indoor unit. If the indoor unit has
no this feature, there is no corresponding operation happeded when press the relative
button on the remote control.
NOTE
NOTE
8
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
AUTO OPERATION
ON/OFF Display: This indicator will be displayed when the unit is operating.
MODE DISPLAY (FAN MODE)
FAN SPEED DISPLAY: Display the selected fan speed: AUTO, HIGH, MED and LOW.
Nothing display when the fan speed is selected, there will be no signal displayed.
FOLLOW ME DISPLAY: When pressing Follow Me button in COOL or HEAT mode,
the remote sensing function is activated and this indicator displays.
TIMER DISPLAY: This display area shows the setting of the TIMER. That is, if only
the Auto-on time function is set, it will display TIMER ON, If only the Auto-off time
function is set it will display TIMER OFF. If both functions are set, it will display TIMER
ON OFF which indicates you have chosen both the Auto-on time and Auto-off time.
LOCK INDICATOR: LOCK display is displayed when pushing the LOCK button. Push
the LOCK button to clear display.
4
5
6
7
8
9
DISPLAY PANEL
Digital Display
TRANSMITION
INDICATOR
OPERATION MODE
INDICATOR
LOCK INDICATOR
FAN SPEED INDICATOR
OPERATION MODE
INDICATOR
ON / OFF
INDICATOR
TIMER DISPLAY
INDICATOR
When you set the air conditioner on AUTO mode, it will automatically select cooling,
heating (Cooling & Heating models only), or fan only operation depending on what
temperature you have selected and the room temperature.
Once you select the operating mode, the operating conditions are saved in the
unit's microcomputer memory.
Thereafter, the air conditioner will start operating under the same conditions when
you simply push the ON/OFF button of the remote control.
1
2
3
4
5
6
8
9
7
9
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
2
2
3
4
1
1
3
Start
Ensure the unit is plugged in and power is available.
The OPERATION Indicator on the display window of the
indoor unit illuminates.
Mode select button (MODE)
Press to select AUTO.
Temperature button (TEMP)
Set the desired temperature normally set it between 21º
C and 28º C.
ON/OFF button
Press the ON/OFF button to start the air conditioner.
Stop
ON/OFF button
Push this button again to stop the air conditioner.
If the AUTO mode is uncomfortable, you can select the
desired conditions manually.
When you select the AUTO mode, you do not have to
set the fan speed. The fan speed will be automatically
controlled.
Start
Ensure unit is plugged and power is available.
Mode select button (MODE)
Press to select COOL, HEAT (Cooling & Heating models
only), or FAN mode.
Temperature button (TEMP)
Set the desired temperature, the most comfortable
temperature is between 21º C and 28º C.
Fan speed button (FAN SPEED)
Press to select "AUTO", "LOW", "MED" and "HIGH"
ON/OFF button
Press the ON/OFF button to start the air conditioner.
The OPERATION Indicator on the display panel of the
Indoor unit illuminates. The operating mode is selected
on accordance with the room temperature and operation
starts after approximately 3 minutes (If you select FAN
mode. The unit will start immediately).
COOL / HEAT / FAN OPERATION
1
2
3
1
2
3
4
10
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
2
3
1
Stop
ON/OFF button
Push this button again to stop the air conditioner.
The temperature cannot be controlled under FAN only mode
While in this mode, only steps 1, 3 and 4 may be performed.
The fan speed cannot be adjusted when the unit is in AUTO and DRY mode.
DRY OPERATION
TIMER OPERATION
Start
Ensure unit is plugged and power is available.
The OPERATION indicator on the display panel of the
indoor unit starts flashing.
Mode select button (MODE)
Press to select DRY.
Temperature button (TEMP)
Push the "TEMP" button to set the desired temperature.
ON/OFF button
Press the ON/OFF button to start the air conditioner. No
fan speed Indicator displays.
The indoor fan speed will be automatically selected LOW.
1
2
3
Stop
ON/OFF button
Push this button again to stop the air conditioner.
In DRY mode, due to the temperature difference between the setting temperature
and the actual indoor temperature, the unit will automatically operate in COOL or
FAN mode.
To press the TIMER ON button can set the auto-on time of the unit. To press the
TIMER OFF button can set the auto-off time of the unit.
NOTE
NOTE
11
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
To set the Auto-on time.
Press the TIMER ON button. The remote control shows
TIMER ON, the last Auto-on setting time and the signal 'h"
will be shown on the LCD display area. Now it is ready to
reset the Auto-on time to START the operation.
Push the TIMER ON button again to set desired Auto-on
lime. Each time you press the button, the lime increases
by half an hour between 0 and 10 hours and by one hour
between 10 and
24 hours.
After setting the TIMER ON, there will be a one half second
delay before the remote control transmits the signal to
the air conditioner. Then, after approximately another
2 seconds. The signal “h” will disappear and the set
temperature will re-appear on the LCD display Window.
To set the Auto-on time.
Press the TIMER OFF button. The remote control shows
TIMER OFF, the last Auto-off setting time and the signal
"h' will be shown on the LCD d splay area. Now it is ready
to reset the Auto-off time to START the operation.
Push the TIMER OFF button again to set desired Auto-off
tune. Each time you press the button, the time increases
by half an hour between 0 and 10 hours and by one hour
between 10 and
24 hours.
After setting the TIMER OFF, there will be a one half
second delay before the remote control transmits the
signal to the air conditioner. Then. after approximately
another 2 seconds, the signal “h” will disappear and
the set temperature will re-appear on the LCD display
window.
1
1
2
2
3
3
3
1
The effective operation time set by the remote control for the timer function is limited to
the following setting: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0,
8.5, 9.0, 9.5, 10, 11, 12, 13,14, 15, 16, 17, 18, 19, 20, 21, 22, 23 and 24.
CAUTIONS
12
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
TIMER ON
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to tum on automatically before say
when you return home. The air conditioner will
automatically start operating at the set time.
Example:
To start the air conditioner in 6 hours.
Press the TIMER ON button, the last setting of starling operation time and the signal
“h” will show on the display area.
Press the TIMER ON button to display “6.0h” on the TIMER ON display of the remote
control.
Wait for about 3 seconds and the digital display area will show the temperature
again. Now this function is activated.
1
1
2
2
3
3
off
Set
Start
8 hours later
TIMER OFF
(Auto-off Operation)
The TIMER OFF feature is useful when you want
the unit to tum off automatically after you go to
bed. The air conditioner will stop automatically
at the set lime.
Example:
To stop the air conditioner in 10 hours.
Press the TIMER OFF button the last setting of stopping operation time and the
signal "h" will show on the display area.
Press the TIMER OFF button to display "10h" on the TIMER OFF display of the remote
control.
Wait for about 3 seconds and the digital display area will show the temperature
again. Now this function is activated.
6.0
h
on
Set
Stop
10 hours later
10
h TIMER OFF
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to stop the air conditioner after you go to bed,
and start it again in the morning when you wake up or when return home.
EXAMPLE OF TIMER SETTING
13
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
5
h TIMER ON OFF
on
Set
Start
Stop
2 hours later
after settings
5 hours later
after settings
Example
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
Press the TIMER OFF button.
Press the TIMER OFF button again to display 2.0h
on the TIMER OFF display.
Press the TIMER ON button.
Press the TIMER ON button again to display 10h on the TIMER ON display.
Wait for the remote control display the setting temperature.
10
h TIMER ON OFF
on
Set
Start
Stop
2 hours later
after settings
10 hours later
after settings
1
2
3
1
4
2
5
3
4
5
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start the
air conditioner before you wake up and stop it
after you leave the house
Example
To start the air conditioner 2 hours after setting
and stop it 5 hours after setting.
Press the TIMER ON button.
Press the TIMER ON button again to display 2.0h on the TIMER ON display.
Press the TIMER OFF button.
Press the TIMER OFF button again to display 5.0h on the TIMER OFF display .
Wait for the remote control to display the setting temperature.
The time setting (TIMER ON or TIMER OFF) that in sequence occurs directly after the set
time will be activated first.
If the same time is set for both TIMER ON and TIMER OFF settings no timer operation
is performed. The air conditioner may stop operating, either immediately or after
approximately 10 minutes.
CAUTIONS
14
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
1
1
2
The sleep function enables the unit to automatically
increase(cooling) or decrease (heating) 1 ºC per hour for
the first two hours, then hold steady for the next 5 hours,
after that the unit will stop operation. It can maintain the
most comfortable temperature and save energy.
SLEEP BUTTON FUNCTION
RESET AND LOCK BUTTON FUNCTION
DIRECTION / SWING BUTTON FUNCTION
The SLEEP function is only available under Cooling, Healing and AUTO operations.
1
1
2
When you press the recessed LOCK button, all current
settings are locked on and remote control does not
accept any operation except that of the LOCK.
Use the LOCK mode when you want to prevent settings
from being changed accidentally
Press the LOCK button again when you want to cancel the
LOCK mode.
A lock symbol will appear on the bottom night hand side
of the remote control display when the LOCK function is
activated.
When you press the recessed RESET button, all current
settings are cancelled and return to original factory
settings.
Use the DIRECTION/SWING button to activate AUTO swing function and lock louver
in desired position.
When press this button once and quickly, the air flow direction setting feature of the
louver is activated. The moving angle or the louver is 6" for each press.
Keep pressing the DIRECTION/SWING button to move the louver to the desired
position.
NOTE
15
REMOTE CONTROLLER
SPLIT AIR CONDITIONER
EPTL
When replacing batteries, do not use old batteries or different type batteries. Otherwise
it may cause the remote control to malfunction.
If you do not use the remote control for 1 few weeks or more, remove the batteries.
Otherwise. batteries leakage may damage the remote control.
The average battery life during normal use approximately half a year. Replace the
batteries when there is no receiving beep from the indoor unit or of the transmission
indicator on the remote control fails to light.
Be sure there are no barriers between the remote control and the receiver of indoor unit
otherwise the air conditioner wilt not work.
Keep the Remote Control away from all liquids.
Protect the Remote Control from high temperatures and exposure to radiation.
Keep the indoor receiver out of direct sunlight or the air conditioner may malfunction.
Keep control away from EMI (Electro-Magnetic Interference) supplied by other household
appliances.
When the louver swing or move to a position which would affect the cooling and heating
enact of the air conditioner, it would automatically change the swing/moving direction
(upward or downward).
1
2
3
4
5
6
7
8
When press the button without releasing for 2 more seconds, the auto swing feature
of the louver is activated. The horizontal louver would swing automatically. Press it
again to stop.
2
CAUTIONS
NOTE