Full Text Searchable PDF User Manual
FMTRON 7W Transmitter Manual
This product uses a new generation of Japanese
ROHM's chip FM stereo radio emission (BH1415F)
Seiko-produced. This machine looks beautiful,
with gold-plated aluminum chassis fully closed,
compact structure, shielding is good, solid firm,
due to BH1415F integrates PLL frequency PLL, audio
pre-emphasis, limiter and low pass filter circuit,
the transmission frequency stability, quality
class, a high degree of stereo separation
performance than the other forums using ROHM's
predecessor (BA1404) produced a more superior
transmitter. Very suitable for the various
tertiary institutions, living quarters, towns and
villages and the need to launch high-power
high-fidelity audio signals to suit the occasion.
The machine operation simple and easy wiring.
Firing frequency of the front panel display using
LCD screen, step to 100Khz, through the bottom of
the "+" and "-" two touch switches to regulate the
frequency of upward and downward, fast and
intuitive. "Audio" as the standard 3.5mm stereo
input jack, you can easily connect to most home
stereo audio playback device. Back on the "DC12V"
for 6.5mm power input socket, through the external
12V/5A (optional larger current margin of) power
adapter input (jack inside the cathode), power
adapter, switching power supply recommended ,
such as notebook computers and LCD monitors and
other external switching power adapter, connector
terminal with a magnetic ring filter is best, so
can greatly reduce the power of the transmitter
interference, conditional use 12V power supply to
the battery of the transmitter .
Machine parameters
Operating Voltage: DC 10V ~ 14V, recommend the use
of 12V;
Operating current: <4A;
Transmission frequency: 87 ~ 108MHz
Transmit Power: 7W
Modulation Mode: FM
Frequency Offset: + /-75KHz
Output Impedance: 50 Europe
Harmonic radiation: <-55dbc
Pre-emphasis delay: 50us;;
Separation: 40dB;
Input Level:-13dBV;
Applicable to the microphone: Electret condenser
microphone
Machine Size: 128mm (L) × 93mm (W) × 55mm (H).
Operation instructions
1. Operation steps: installing an antenna---->>>
to connect the power ---->>>to connect audio
source---->>> to connect the microphone
2. Press the power button to boot into normal
working condition.
AS the step of the bottom:
In the back of the transmitter, the antenna
interface (ANT) as a BNC interface, therefore, the
antenna interface should also be as BNC. External
power adapter output voltage DC10 ~ 14V should be
within the range of maximum output current should
be in 2A above. As shown, the power adapter DC plug
connected to the transmitter back "DC12V" on top
of the power socket (Note the polarity is correct,
he is outside the negative)
As shown above, for connecting external sound
source audio lines connected to "AUDIO" interface.
Should use more cable shielding performance audio
cable, 3.5mm plug.
Connect the microphone
Connected to the "MIC" jack. And audio cable,
like a good selection of shielding wires, plugs
for 3.5mm. (Note: The microphone for the
microphone type is Electret condenser microphone.
Boot
After all the preparation work was ready, the
power adapter open, the transmitter is in standby
mode the screen displays "OFF":
Click on the front panel , The transmitter
will enter the normal working state, and then,
through the "+" or "-" It's two buttons to adjust
the working frequency of the machine required
frequency.
Special features of the setting and adjustment
1.Power Adjustment
The machine output power sub-two tranches:
Power profile (H):7W; low-power profile (L):1.5W
First of all, turn off the power adapter (or
disconnect DC12V), finished in the transmitter
power lines disconnected state, press and Hold
, And then connect the power adapter (that is,
DC12V connected to the transmitter), 3 seconds
after release the button, this time into the power
to adjust the state, LCD display shows "L" or "H":
Click "+", set to high power (H), according to "-",
set for low-power (L), select the desired power
profile, and then , Power is set, it will go
to set the frequency range of the state.
2.Frequency range setting
The completion of power set, will enter a
frequency range to set the state. Power setting
is completed, press the , LCD screen display a
group of frequency data, frequency data is the
work of this group of high-end frequency band. For
example, to set the operating frequency range from
90MHz ~ 100MHz, then at this time through the "+"
"-" button, adjust the frequency data is 100.00MHz,
band, high-end is set up, press , Will enter
the low-end frequency setting, LCD display data
for low-frequency band, through the "+" "-" button,
adjust the data for 90.00MHz, and then At this
time, is set up (note that band-band high-end
low-end can not be compared even higher), this
machine by default, within 87 ~ 108MHz to ensure
that all performance indicators, generally in the
83 ~ 115MHz can also be used normally, if the super
- they range, you need to modify the parameters
of the internal components.
3. Attention
(1)Before booting, be sure to had connect
the antenna. It is strictly prohibited empty boot.
(2) Audio cable must use shielded cable.
(3)The power adapter output DC voltage is
selected as clean, so as not to interfere with the
transmitter.
(4) Avoid extreme hot or humid environment.
4. General troubleshooting.
A.The frequency can not be adjusted.
Reason: to set the frequency range may
be errors, high-frequency than low-end high
frequency.
Solution: re-setting the relevant
parameters (see instructions)
B. To open the boot method, press the power
button, the flash look, LCD displays "OFF"
Reasons: low-voltage, over-power
adapter with a lower load capacity.
Solution: replace the power adapter
(12V/1A)
C. Sound distortion serious
Cause: The input audio amplitude is
too large.
Workaround: down the volume of the
sound source.
D. Launch proximity
Reason: There may be power set to low
power file (L)
Solution: re-setting power
parameters.
FMTRON: CZH-7C
7W Fm Transmitter mini Radio Station PLL LCD
Come w/Antenna, Power Adapter, Audio Cable
Warning:
The equipment is only good for home, church or small building for private purpose and you must
follow FCC regulations.
Package included:
•
7W Transmitter x1
•
Antenna (optional)
•
Audio Cable (optional)
•
Power Adapter (optional)
Power Output:
7W ±20%(Use 10V DC)
FM Transmitter Frequencies: 87-108Mhz
Tuning Step:
100Khz/0.1Mhz
Power Supply:
9-12V DC (The current load of power supply should over 1A)
Stability of Frequency:
±0ppm
(
-10
℃
~+50
℃
)
Frequency Response:
100 - 15000Hz
Signal to Noise Ratio:
>70dB
Distortion:
< 0.5%
Operation Time:
True 24/7
Antenna Design:
Metal Antenna
Antenna Connector:
BNC type
Output Impedance:
50 ohm
Audio Input Connector:
3.5mm headphone connector
Mic Input Connector:
3.5mm headphone connector
Tuning Design:
Stable PLL Technology
Size of Transmitter Unit:
L:113mm, W:88mm, H:39mm
Weight of Transmitter Unit:
N/A
Transmission Signal:
FM Stereo
* To set the transmit power, push the power button down and hold it then connect DC supply at the same time.
When the LCD screen starts to display H or L, press "+" or "-" button to switch between H and L. "H" stands
for 7w, L stands for 1.5W.
* We did pre-test equipment before ship, whenever you turn on power you must connect Loader or Antenna on
RF output, otherwise you will burn down the RF amplifier. Please be aware of this we will reject your return on
such case.
* The warranty is void if physical damage, customer's misuse, accident or modifies the unit.
* The detail user manual feel free download from
www.fmtron.com/download.php