PDF User Manual

  1. Home
  2. Manuals
  3. NEEWER NW-870 Manual

NEEWER NW-870 Manual

Made by: NEEWER
Type: Manual
Category: Remote Control
Pages: 12
Size: 1.80 MB

 

Download PDF User Manual



Full Text Searchable PDF User Manual



background image

Camera Wireless Timer Remote

NW-870

Manual

BULB

1- 59"

NW-870Tx 

CH+

CH-

NW-870 Wireless Rx

 


background image

      Thanks so much purchase NEEWER product,NW-870 is high performance wireless 
timer remote control. It is available option of wired or wireless in single, low speed/high 
speed continuous, bulb, delay shooting and timer planning shooting mode.Please read 
carful and understand the way of use camera, before use YouPro wireless timer remote 
control, in order to know the better way of use our product.

Overview

01

Caution before use

Make sure the camera is power off before install the device of the YP-870RX, When 

the product connect the device, please not pull the cable.

This component can’t be strong vibration, or may lead to product failure.

Please turn off the battery if such long time won’t use this product.

Please not use flammable gases in violation of this warning may cause an 

explosion or fire.

It is a electronic product accessories, some of the environment condition may affect 

the working, however it is much less probability of this condition, please don’t worry.

Please not put our product in high tempura area, such as a closed car under direct 

sunlight, the control panel and the other high-temperature area.

Please keep dry, do not use wet hand contact with the product, the product must not 

be immersed in water or exposed to rain, and this may lead to not work properly.

Because of this product is included battery, please strictly follow the instruction for 

operation. Otherwise it may cause an explosion, fire or personal injury.

 


background image

1. Transmitter (NW-870TX)                                                                           
2. Receiver(NW-870RX)                                                                
3. Connect cable                                                                                         
4. Manual                                                                      
5. AAA battery (3V)                                                                        
6. CR-2 battery(3V) 

Included Items

2.5mm connect plug

2.camera cable connect.

1

2

02

Function Introduction

Adopt free global FSK2.4GHz signal, more stable, the operate distance can reach 

more than 100m
YP-870 TX also work as wired remote control, also support single, low speed/high 

speed continuous, bulb, delay shooting and timer planning shooting mode.
YP-870 TX also support plug the camera connect cable to work as wired remote 

when power off.

Support LCD display, The channel information of transmit and receiver are displayed 

on the screen, clear and easy to operate.
Support change the shutter connecting cable for different camera models to control 

different brand and different models cameras.

32 channels available, prevent the signal disturb through set different groups.

Please check the below items in the package, please contact the dealer if there is 

missed some items.

1pc
1pc
1pc
1pc

1pc

2pc

Camera connect cable introduction

 


background image

03

16

17

CH+

CH-

BULB

1- 59"






10

11

13

15

14

12

Transmitter

Instruction of product component

1. Indictor light

2. LCD display screen

3. BULB shooting button

4. Single shooting /low speed shooting/high speed shooting button

5. Delay shooting button

6. Timer plan shooting button

7. Power button/CH button

8.Shutter release button

9. 2.5mm output port

10. Numerical increase button

11. Timer plan start/ stop button

12. Turn right button

13.Setting button/lock or unlock button 14. Numerical reduce button

15. Turn left button

16. Product sticker

17. Battery cover

Receiver

1. LCD display screen
2. Indictor light
3. Power button/CH button
4. CH+ button
5. Battery cover
6. Screw nut
7. Fix foot
8. 1/4’’ screw
9. 2.5mm output port

NW-870 Wireless Rx

 


background image

1. Open the battery cover

2. Install the CR-2 battery in  right way + and –,

3. Close the battery cover

04

BULB



10

11 12

13

Icon name of TX LCD display screen

Install and use

1. Open the battery cover

2. Install the battery in  right way + and –

3. Close the battery cover

The way of install the battery of transmitter

The way of install the battery of receiver

Caution to install the positive and negative terminals of the battery.

1. Repeat plan shooting times icon
2. Repeat timer plan shooting interval time icon
3. Timer shooting picture number
4. Timer shooting interval time icon
5. Timer plan shooting exposure time icon
6. Timer plan delay icon
7. Time and status icon
8. Single shooting/low speed shooting/high speed

    shooting icon
9. Delay shooting icon
10. Bulb shooting icon 11. Time shooting plan icon
12. Lock button icon 13. CH icon

Icon name of RX LCD display screen

CH icon

 


background image

Fix the(NW-870RX)

Set the communication channels 

Receiver (RX) to connect the camera 

Set transmitter (TX) channels

Set the receiver (RX) communication channels 

05

Support install the receiver in the hot-shoe, bracket and tripod and so on.

BULB

CH+

CH-

1. Put the receiver screw on 
the camera hot shoe(Picture1)

2. Fixed the receiver in 
camera plate(Picture2)

3. Fixed the receiver in 
tripod(Picture3)

Please ensure the transmitter (TX) and Receiver (RX) on same channels, support 

set 32 channels.

1. Press 2 second of power and press [CH]button, the 

number of channels icon will flicking 

2. Press [+] or [-] to adjust the channels number.

3. Press the button[S/L]again to keep the current channels 

number.

*  if the transmitter work as wired remote control won’t need adjust the parameter setting.

1. Press 2 seconds power button

2. Press [CH+] or [CH-] button, the channels number icon will 

flicker.

3. Press [CH+] or [CH-] to adjust the channels 

4. Both press [CH+] or [CH-] or not operation after 6seconds, 

keep it and back to channels setting.

1. Ensure the receiver and camera is power off, first insert connect cable to camera

 


background image

Use the device

Single shooting⁄low continuous shooting⁄high speed continuous shooting 

06

Single shooting mode

BULB

BULB

BULB

*Ensure the cable and camera is connecting.

2.  Install  the camera to tripod or the other bracket and open 

the camera protector ,insert the cable to camera.

3.  Turn on the receiver and camera power.

*The transmitter (TX) is used as wired camera remote, 

  connect the cable to camera.

Transmitter(TX)in working status, press [        ] button, the transmitter rapid to the 

function of single shooting, low speed continuous shooting or high speed continuous 

shooting mode, the screen will display the icon of “        ”.

Press the button(S/L), the screen will display “time and status of icon flicker”.

Press again of [+] or [-] button, switch to “CS(single shooting), CL(low speed 

continuous shooting) or CH( high speed continuous shooting mode” see below 

picture

Low speed continuous shooting High speed continuous shooting

Press half shoot release, blue lighting on, camera is in zooming state.

Full press the camera release, red signal is on, camera is in working.

1. 

2. 
3. 

4. 
5. 

*Transmitter is in CS(Single shooting mode), full press release button is in single shooting.
*Transmitter is in CL( Low speed continuous shooting mode),full press the shooting button
  not release, camera is in low speed shooting mode until the release the shooting button.
*Transmitter is in CH(High speed continuous mode),full press shooting button and not release
  camera in CH until release the shooting button.
*Low continuous shooting and high speed continuous shooting mode not need set camera in 
 same mode.

 


background image

07

[BULB] shooting mode

BULB

Delay shooing mode

Delay parameter setting:

BULB

1. 

2. 

3. 

1. Ensure the camera in [BULB] mode 

2. Press transmitter in [BULB] mode, the screen will display 

[BULB] (Same as picture)

3. Half press the shooting button, blue lighting will be on and 

the camera is in zooming.

4. Full press the shooting button, red lighting will flicker and start to work, the product 

will be on output the signal and in BULB shooing mode.

5. Press the shooting release button again, the remote will be stopped the signal 

mode, complete the BULB shooting mode.

1. Press the transmitter[       ]button, the screen will display

[       ]camera is in delay shooting mode.(Left picture)

2. Press the [S/L] button, product is in delay shooting mode, the 

shooting icon will flicker, press the number [+] or number [-] and set 

the delay interval time (1-59 seconds) as (Picture A).

3. Turn left button[       ] into the setting of delay shooting mode, 

through [+] or [-] setting the shooting picture number (1-99), see left 

(Picture B)

4. After the parameter setting, press the button[S/L] to save it and exit. 

Delay shooting mode operation

Half press the shooting release button, the blue lighting is on and the camera is in 

zooming state.

Full press the shooting release button, the remote control is in count down, red signal 

flicker and into the delay shooting state.

End of count down mode, the  remote control will set the shooting picture number, 

each seconds will output the signal to control the camera.

 


background image

08

Timer plan shooting mode

BULB

A: Timer remote parameter setting

LONG

LONG

LONG

exposure hour

setting

exposure minute

setting

exposure seconds

setting

1. 

1. 

2. 

3. 

4. 

2. 

3. 

4. 

The transmitter press the button[        ], the LCD screen will 

display icon[       ]and will into timer remote mode, see(left 

picture)

a. Delay shooting setting mode:

a. Delay shooting setting mode:

b. Exposure time setting

Turn left button[        ]or turn right button[        ], choose the delay shooting icon of 

[DELAY].

Press the number button [+] or [-] ,if press it not release, the number will rapid to 

increase or reduce.
Press the button  save and exit it.

Turn left button[        ]or right button[        ]choose the icon of exposure [LONG].

Press the setting button[S/L]  into the delay time of “seconds” setting, through press 

button[        ]or right button[        ]into the “Minute” and “Hour” setting.

Press the number button [+] or [-] ,if press it not release, the number will rapid to 

increase or reduce.

 Press the button[S/L]  save and exit it.

Press the button[S/L]  into the delay time of “seconds” setting, through press the 

left button[        ]or right button[        ]into “Minute” and hour setting ,see the (below 

picture.) 

DELAY

DELAY

DELAY

exposure hour

setting

exposure minute

setting

exposure seconds

setting

Press

Press

Press

Press

Press

Press

Press

Press

 


background image

09

c. Interval time shooting setting mode

d. Shooting number of picture setting

e. Repeat timer plan interval shooting setting

1. 

3. 

3. 

1. 

2. 

3. 

4. 

2. Press the setting button[S/L]into the delay time of “seconds” setting, through press 

button[        ]or right button[        ]into the “Minute” and “Hour” setting.

1.Turn left button[        ]or turn right button[        ],choose the   icon of [INTVL].

Turn left button[        ]or right button[        ]choose the icon of 

[N1]
Press the setting button[S/L]into the timer shooting picture 

number mode see [left picture].

Press the number button [+] or [-] ,if press it not release, the number will rapid to 

increase or reduce of the number of picture(support set the picture number from 

1-99).

4. Press the button[S/L],save and exit it.

Press the number button [+] or [-] ,if press it not release, the number will rapid to 

increase or reduce.

4. Press the button[S/L]save and exit it.

Press the number button[+]or [-] ,if press it not release, the number will rapid to 

increase or reduce.
Press the button[S/L]save and exit it.

INTVL

INTVL

INTVL

exposure minute

setting

exposure hour

setting

exposure seconds

setting

Press

Press

Press

Press

RE

RE

RE

repeat interval time

setting

repeat interval time

setting

repeat  interval time 

setting

Press

Press

Press

Press

Turn left button[        ]or right button[        ]choose the icon of  [RE] from the LCD 

screen.

2. Press the setting button[S/L]  into the repeat interval shooting of “seconds” setting, 

through press button[        ]or right button[        ]into the “Minute” and “Hour” setting. 

 


background image

10

N2

Repeat plan times setting

Unlimited repeat plan explain

N2

D. The photo of timer plan shooting

BULB

CH

S/L

DELAY

LONG

LONG

INTVL

INTVL

INTVL

LONG

LONG

 N1=1

 N1=2

N1=3

 N1=n

1. 

2. 

f. Repeat plan times setting

1. Turn left button[        ]or right button[       ]choose the icon of 

[N2]from the LCD screen.

2. Press the setting button[S/L]into the repeat time setting, 

see (Left picture)

3. Press the number button [+] or [-], set the number increase or 

reduce ( support repeat plan times from 1-99)

when the number 

display , it mean unlimited time, see (left picture)

4. Press the button  save and exit it.

B. Query the timer shooting plan

Turn left button[        ]or right button[        ]query every timer plan or option and 

parameter. If need set the parameter in some option, through timer plan parameter 

indication to setting.

1. 

C. Timer plan shooting operation

Turn on the power, press time plan button[        ]the LCD screen will display timer 

plan shooting icon[        ].

Press the timer plan shooting button[        ]see (left picture) 

Transmitter transfer all the information to receiver ,the 

lighting of transmitter and receiver lighting will be flicker, 

timer plan shooting is in working, the transmitter control the 

camera. The transmitter will display the information of timer 

plan shooting condition.

3. In the timer plan state, press the transmitter of timer plan[        ]button again, the 

transmitter and receiver will 

Repeat interval time

(RE)

Press N2 cycle repeat

 


background image

100m

63

mm

X38

mm

X27.5

mm

135.5

mm

X44

mm

X17.8

mm

Product Specification

System mode

FSK 2.4G

Operation Channel

32th

Operation distance

Battery 

AAA*2 CR2*1

The receiver standby time

The transmitter standby time

1000hours
300hours

The dimension of transmitter
The dimension of receiver

Add:Room 3603 Shen Fang Plaza
No.3005,Renmin South Road Luo Hu district
Shenzhen,Guangdong 518005,China
TEL:+86-755-22954335
Email: Support@neewer.com
Web: www.neewer.com

Shen Zhen Neewer Technology Co.,Ltd

Above is the manual of NW-870,If you need any help, please contact our dealer or 
browse website:www.neewer.

com