Full Text Searchable PDF User Manual
SE90.2 / SE150.2/SE90.4 / SE150.4
SE800.1 / SE1500.1/SE2000.1 / SE3500.1
DSP DIGITAL POWER AMPLIFIERS
OWNER'S MANUAL
2
FEATURES
Overload, shortcircuit, thermal, low voltage protection
Power Supply Design: Full MOSFET DC-DC PWM Power Supply
Double side FR-4 PCB,High quality SMD components
Delay Time
(
0-20ms / 0.02ms step
) &
Delay Time Trim set
adjustable;
4 bands Customized EQ with adjustable Q factor;27 bands fixed EQ with
fixed Q factor
Full range Crossover Slope 6dB - 48dB
(
HP/ BP/ LP
)
All settings stored in the amps will be saved as presets for the next turn-
on.
All settings can be saved and upload to software as a preset, convenient to
offer long-distance aids to customers.
Professional software with intuitive user interface,Supporting multiple
operation systems like Windows XP/ vista / Win7, Android & Apple OS
Wireless remote controller to switch 4 settings in real-time
Special WIFI adapter to actualize the wireless communications with
software
4 Settings Memory Stored Function
Built-in Professional DSP circuit
Congratulations on your purchase of a SOUNDMAGUS state-of-the-art
power amplifier with digital signal processing. At SOUNDMAGUS Mobile
Audio we strive to provide some of the latest technology tools that make
the quest for “the perfect tune” so much easier. Our goal was to develop
technologically advanced amplifiers completely adjustable to the acoustics
of each vehicle.
INTRODUCTION
A power amplifier’s performance is only as good as its installation.
Proper installation will maximize the system’s overall performance. It is
recommended that you have our product installed by an authorized
SOUNDMAGUS retailer. However, if you decide to install it by yourself,
please carefully read through this manual and take your time to do a
qualified installation.
RECOMMENDATION
1
2
FEATURES
Overload, shortcircuit, thermal, low voltage protection
Power Supply Design: Full MOSFET DC-DC PWM Power Supply
Double side FR-4 PCB,High quality SMD components
Delay Time
(
0-20ms / 0.02ms step
) &
Delay Time Trim set
adjustable;
4 bands Customized EQ with adjustable Q factor;27 bands fixed EQ with
fixed Q factor
Full range Crossover Slope 6dB - 48dB
(
HP/ BP/ LP
)
All settings stored in the amps will be saved as presets for the next turn-
on.
All settings can be saved and upload to software as a preset, convenient to
offer long-distance aids to customers.
Professional software with intuitive user interface,Supporting multiple
operation systems like Windows XP/ vista / Win7, Android & Apple OS
Wireless remote controller to switch 4 settings in real-time
Special WIFI adapter to actualize the wireless communications with
software
4 Settings Memory Stored Function
Built-in Professional DSP circuit
Congratulations on your purchase of a SOUNDMAGUS state-of-the-art
power amplifier with digital signal processing. At SOUNDMAGUS Mobile
Audio we strive to provide some of the latest technology tools that make
the quest for “the perfect tune” so much easier. Our goal was to develop
technologically advanced amplifiers completely adjustable to the acoustics
of each vehicle.
INTRODUCTION
A power amplifier’s performance is only as good as its installation.
Proper installation will maximize the system’s overall performance. It is
recommended that you have our product installed by an authorized
SOUNDMAGUS retailer. However, if you decide to install it by yourself,
please carefully read through this manual and take your time to do a
qualified installation.
RECOMMENDATION
1
SE800
.
1
/
SE1500
.
1
/
SE2000
.
1
/
SE3500
.
1
CONTROLS & FUNCTIONS
SE90.2/SE150.2
SE800
.
1
/
SE1500
.
1
SE2000
.
1
/
SE3500
.
1
SE90.2/SE150.2
SE90.4/SE150.4
3
Connect speakers/subwoofers to these terminals. Be sure to check wire for proper
polarity. Never connect the speaker cables to chassis ground.
1
2
3
4
5
8
7
6
1. SPEAKERS
5
8
7
6
1
2
3
4
SE90.4
/
SE150
.
4
CONTROLS & FUNCTIONS
the vehicle battery or the positive terminal of an isolated audio system battery.
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of
2. +12 Volt Power
remote turn on lead of the head unit or signal source.
This terminal turns on the amplifier when (+)12 volt is applied to it . Connect it to the
3.Remote Turn On
stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a
good idea to replace the factory ground at this time with a larger cable equal to the new amplifier
power cable or larger.
CAUTION:
Do not connect this terminal directly to the vehicle battery ground terminal or any
other factory ground points.
Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been
4.GND
1
2
3
4
5
8
7
6
4
SE800
.
1
/
SE1500
.
1
/
SE2000
.
1
/
SE3500
.
1
CONTROLS & FUNCTIONS
SE90.2/SE150.2
SE800
.
1
/
SE1500
.
1
SE2000
.
1
/
SE3500
.
1
SE90.2/SE150.2
SE90.4/SE150.4
3
Connect speakers/subwoofers to these terminals. Be sure to check wire for proper
polarity. Never connect the speaker cables to chassis ground.
1
2
3
4
5
8
7
6
1. SPEAKERS
5
8
7
6
1
2
3
4
SE90.4
/
SE150
.
4
CONTROLS & FUNCTIONS
the vehicle battery or the positive terminal of an isolated audio system battery.
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of
2. +12 Volt Power
remote turn on lead of the head unit or signal source.
This terminal turns on the amplifier when (+)12 volt is applied to it . Connect it to the
3.Remote Turn On
stripped of all paint down to the bare metal. Use the shortest distance possible. It is always a
good idea to replace the factory ground at this time with a larger cable equal to the new amplifier
power cable or larger.
CAUTION:
Do not connect this terminal directly to the vehicle battery ground terminal or any
other factory ground points.
Connect this cable directly to the frame of the vehicle. Make sure the metal frame has been
4.GND
1
2
3
4
5
8
7
6
4
6
PREINSTALLATION
Please prepare sufficiently to layout your car space before installation. We
recommend to have the installation done by an Autho rized SOUNDMAGUS
Dealer.
Please use good insulated power cable to endure longterm above 40A
electronical current. The +12 Volt power cable must be connected with a
fuse in line near 20cm of battery+ terminal. Required current, power
cable and proper external fuse listed as following:
MODEL
CABLE
FUSE
SE800
.
1
4
#
80
A
SE1500
.
1
2
-
4
#
120
A
SE2000
.
1
0
-
4
#
200
A
SE3500
.
1
0
-
2
#
300
A
SE90
.
2
8
#
30
A
SE150
.
2
4
-
8
#
40
A
SE90
.
4
40
A
SE150
.
4
4
-
6
#
60
A
4
-
8
#
Please use car audio RCA cables, otherwise it may be disturbed. Keep
these cables as short as possible. To avoid disturbances from your car
electronics, please don`t close the existing car cables when you install
the RCA cables.
Don't expose any cables out of car. Please take care insulated cables to
avoid damaging when cables pass through metal, rubber and plastic
etc. Don't install all cables too tight.
The ground wire should be connected directly with the chassis of your
vehicle which should be metal to metal ground point connection.
The amplifier must be mounted securely at a solid, dry and low vibration
surface in the trunk or passenger area. Fix the amplifier in an open air
area to insure proper heat dissipation.
5
CONTROLS & FUNCTIONS
SE800
.
1
/
SE1500
.
1
SE2000
.
1
/
SE3500
.
1
SE90.2/SE150.2
SE90.4/SE150.4
with a minimum level of 200mV is required for proper operation. The use of high quality twisted
pair cables is recommended to decrease the possibility of radiated noise entering the system.
These RCA input jacks are for use with source units that have RCA outputs. A source unit
5. RCA Input Jacks
The red LED will light up and will be flashing if there is a fault presented to the amplifier.
Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
7. Alarm Indicator
This LED will light up when amplifier works properly.
8. RUN
WI - FI adapter. Connection amplifier and adapter wap - set crossover and function. Once set
up completed, WI - FI adapter can be pulled out, latest settings will be saved in the amplifier.
6. I/O PORT
6
PREINSTALLATION
Please prepare sufficiently to layout your car space before installation. We
recommend to have the installation done by an Autho rized SOUNDMAGUS
Dealer.
Please use good insulated power cable to endure longterm above 40A
electronical current. The +12 Volt power cable must be connected with a
fuse in line near 20cm of battery+ terminal. Required current, power
cable and proper external fuse listed as following:
MODEL
CABLE
FUSE
SE800
.
1
4
#
80
A
SE1500
.
1
2
-
4
#
120
A
SE2000
.
1
0
-
4
#
200
A
SE3500
.
1
0
-
2
#
300
A
SE90
.
2
8
#
30
A
SE150
.
2
4
-
8
#
40
A
SE90
.
4
40
A
SE150
.
4
4
-
6
#
60
A
4
-
8
#
Please use car audio RCA cables, otherwise it may be disturbed. Keep
these cables as short as possible. To avoid disturbances from your car
electronics, please don`t close the existing car cables when you install
the RCA cables.
Don't expose any cables out of car. Please take care insulated cables to
avoid damaging when cables pass through metal, rubber and plastic
etc. Don't install all cables too tight.
The ground wire should be connected directly with the chassis of your
vehicle which should be metal to metal ground point connection.
The amplifier must be mounted securely at a solid, dry and low vibration
surface in the trunk or passenger area. Fix the amplifier in an open air
area to insure proper heat dissipation.
5
CONTROLS & FUNCTIONS
SE800
.
1
/
SE1500
.
1
SE2000
.
1
/
SE3500
.
1
SE90.2/SE150.2
SE90.4/SE150.4
with a minimum level of 200mV is required for proper operation. The use of high quality twisted
pair cables is recommended to decrease the possibility of radiated noise entering the system.
These RCA input jacks are for use with source units that have RCA outputs. A source unit
5. RCA Input Jacks
The red LED will light up and will be flashing if there is a fault presented to the amplifier.
Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
7. Alarm Indicator
This LED will light up when amplifier works properly.
8. RUN
WI - FI adapter. Connection amplifier and adapter wap - set crossover and function. Once set
up completed, WI - FI adapter can be pulled out, latest settings will be saved in the amplifier.
6. I/O PORT
8
4) After
The
Plastic
Cap
Is
Stick
To
The
Amp
,
Holding
Two
Ends
Of
The
Plastic
Caps
(
As
Shown
In
Figure 3
)
And
Push
them
down to the same horizontal level
(
As
Shown
In
The
Figure 3
).
Holding
both
ends
of
the
plastic
cap
,
push
down
together
with
same
strength
.
Figure 3:
6) When
removing the plastic end caps
,
hold
two ends of the plastic cap
(
as shown in
the following figure) and pull
them up about 2mm from the amp
.
Then they can be
taken away parallelly
.
Holding
both
ends
of
plastic
cap
and
remove
it
parallelly
5)
Plastic
cap
installation
completed
.
7
AMPLIFIERS INSTALLATION
2 ) Using attached screws to fix the amplifier to the chosen place.(As shown in figure 1)
3 )
Each
plastic
end
cap
has
5
buckles
that match 5 buckle
holes
on the amplifier
.
Hold
two
ends
of
the
plastic end cap and
push it towards the amps horizontally
.(
As
shown in figure 2)
1 ) Choosing a flat and ventilated place to install amplifier.
Be sure to carefully read and understand the instructions before attempting to
install the Amplifier.
1
.
Installation steps
Ho
riz
on
tal p
ush d
ire
cti
on
Ho
riz
on
tal p
ush d
ire
cti
on
Figure 1 :
Figure 2 :
Plastic End Caps Fastening Illustration
8
4) After
The
Plastic
Cap
Is
Stick
To
The
Amp
,
Holding
Two
Ends
Of
The
Plastic
Caps
(
As
Shown
In
Figure 3
)
And
Push
them
down to the same horizontal level
(
As
Shown
In
The
Figure 3
).
Holding
both
ends
of
the
plastic
cap
,
push
down
together
with
same
strength
.
Figure 3:
6) When
removing the plastic end caps
,
hold
two ends of the plastic cap
(
as shown in
the following figure) and pull
them up about 2mm from the amp
.
Then they can be
taken away parallelly
.
Holding
both
ends
of
plastic
cap
and
remove
it
parallelly
5)
Plastic
cap
installation
completed
.
7
AMPLIFIERS INSTALLATION
2 ) Using attached screws to fix the amplifier to the chosen place.(As shown in figure 1)
3 )
Each
plastic
end
cap
has
5
buckles
that match 5 buckle
holes
on the amplifier
.
Hold
two
ends
of
the
plastic end cap and
push it towards the amps horizontally
.(
As
shown in figure 2)
1 ) Choosing a flat and ventilated place to install amplifier.
Be sure to carefully read and understand the instructions before attempting to
install the Amplifier.
1
.
Installation steps
Ho
riz
on
tal p
ush d
ire
cti
on
Ho
riz
on
tal p
ush d
ire
cti
on
Figure 1 :
Figure 2 :
Plastic End Caps Fastening Illustration
10
WIRING DIAGRAM
SE90.2/SE150.2 Amplifier wiring
CD
speaker impedance
2~4
O
hm
Input 2 Channel Mode
Bridged Mode
Stereo Mode
speaker impedance
2~4
O
hm
SUB WOOFER
speaker impedance
4~8
O
hm
9
WIRING DIAGRAM
SE800.1/1500.1/2000.1/3500.1 Amplifier wiring
CD
SUB WOOFER
speaker impedance
1~4
O
hm
SUB WOOFER
speaker impedance
2~8
O
hm
SUB WOOFER
speaker impedance
2~8
O
hm
Single channel input Mode
Two Woofer Load Mode
One Woofer Load Mode
10
WIRING DIAGRAM
SE90.2/SE150.2 Amplifier wiring
CD
speaker impedance
2~4
O
hm
Input 2 Channel Mode
Bridged Mode
Stereo Mode
speaker impedance
2~4
O
hm
SUB WOOFER
speaker impedance
4~8
O
hm
9
WIRING DIAGRAM
SE800.1/1500.1/2000.1/3500.1 Amplifier wiring
CD
SUB WOOFER
speaker impedance
1~4
O
hm
SUB WOOFER
speaker impedance
2~8
O
hm
SUB WOOFER
speaker impedance
2~8
O
hm
Single channel input Mode
Two Woofer Load Mode
One Woofer Load Mode
12
AMPLIFIER AND WIFI WIRING DIAGRAM
WAP-1 And amplifier connection steps
Connection steps
1
.
Make
sure
of
correct wiring of amplifier
(Such as 9 ~ 11 page).
2
.
Using special connecting line will wi - fi adapter (WAP -1) and amplifier connection.
3
.
Start the amplifier to work normally
.
Wireless Connecting with PC and software steps
1
.
Link the DSP AMP Wi-Fi on PC with password.
2
.
Click on open DSP operating software, into the DSP interface.
4
.
When the wireless icon shows green, it indicates successful connection and you can
3
.
Right-click the DSP software interface the top left corner of the wireless icon, click
"select device", select the popup menu in the connection Wi - Fi equipment, Click on
the "selete" connection.
begin your setup
.
11
WIRING DIAGRAM
SE90.4/SE150.4 Amplifier wiring
Input 4 Channel Mode
3 - Channel Mode
4 - Channel Mode
SUB WOOFER
speaker impedance
4~8
O
hm
CD
2~4
O
hm
speaker impedance
2~4
O
hm
speaker impedance
2~4
O
hm
2~4
O
hm
2~4
O
hm
2~4
O
hm
Bridged
12
AMPLIFIER AND WIFI WIRING DIAGRAM
WAP-1 And amplifier connection steps
Connection steps
1
.
Make
sure
of
correct wiring of amplifier
(Such as 9 ~ 11 page).
2
.
Using special connecting line will wi - fi adapter (WAP -1) and amplifier connection.
3
.
Start the amplifier to work normally
.
Wireless Connecting with PC and software steps
1
.
Link the DSP AMP Wi-Fi on PC with password.
2
.
Click on open DSP operating software, into the DSP interface.
4
.
When the wireless icon shows green, it indicates successful connection and you can
3
.
Right-click the DSP software interface the top left corner of the wireless icon, click
"select device", select the popup menu in the connection Wi - Fi equipment, Click on
the "selete" connection.
begin your setup
.
11
WIRING DIAGRAM
SE90.4/SE150.4 Amplifier wiring
Input 4 Channel Mode
3 - Channel Mode
4 - Channel Mode
SUB WOOFER
speaker impedance
4~8
O
hm
CD
2~4
O
hm
speaker impedance
2~4
O
hm
speaker impedance
2~4
O
hm
2~4
O
hm
2~4
O
hm
2~4
O
hm
Bridged
13
规格
参数
附表
1
附表
2
若有
其它
问题
请联
系“
圣坛
美歌
指定
安装
店”
或登
陆官
方网
ww
w
.
.c
om
获
得相
关技
术支
持。
SO
UN
DM
AG
US
型号
通道
4
欧姆
额定
负载
2
欧姆
额定
负载
最大
功率
SE
90
.2
SE
15
0.2
SE
90
.4
SE
15
0.4
2
2
4
4
80
W x 2
13
5W x 2
80
W x 4
13
5W x 4
12
0W x 2
16
0W x 2
12
0W x 4
16
0W x 4
4
欧姆
桥接
负载
23
0W x 1
32
0W x 1
23
0W x 2
32
0W x 2
48
0W
64
0W
96
0W
12
80
W
24
3 x 20
2 x5
6
26
3 x 20
2 x5
6
31
3 x 20
2 x5
6
38
0 x 20
2 x5
6
尺寸
(
毫米
)
(
长
) x (
宽
) x (
高
)
32
0W x 1
58
0W x 1
66
0W x 1
58
0W x 1
55
0W x 1
98
0W x 1
11
50
W x 1
11
50
W x 1
型号
通道
4
欧姆
额定
负载
2
欧姆
额定
负载
最大
功率
尺寸
(
毫米
)
(
长
) x (
宽
) x (
高
)
SE
80
0.1
SE
15
00
.1
SE
20
00
.1
SE
35
00
.1
单声
道
31
00
W x 1
16
00
W
30
00
W
40
00
W
72
00
W
35
1 x 20
2 x5
6
42
8 x 20
2 x5
6
44
5 x 20
2 x5
6
58
8 x 20
2 x5
6
1
欧姆
额定
负载
0
.
5
欧姆
额定
负载
80
0W x 1
14
00
W x 1
19
00
W x 1
19
00
W x 1
单声
道
单声
道
单声
道
故障
对策
电源
指示
灯不
亮
检查
音频
信号
源的
音量
控制
器
电源
指示
灯亮
,
但仍
没有
声音
检查
PC
软件
的
MU
TE
功能
是否
开启
检查
音频
信号
线及
其连
接情
况
检查
扬声
器是
否损
坏及
其连
接线
是否
正确
检查
电源
线和
接地
线是
否正
确连
接
检查
开关
控制
线是
否和
机头
的音
源设
备正
确连
接
检查
所有
的保
险管
是否
损坏
检查
蓄电
池电
压是
否过
低
功放
处于
保护
状态
检查
功放
扬声
器输
出端
是否
短路
,扬
声器
是否
损坏
检查
功放
温度
是否
过高
检查
扬声
器阻
抗是
否正
确
检查
电池
电压
是否
过低
音色
失真
检查
音源
设备
音量
是否
过大
,超
出了
本机
或扬
声器
的正
常工
作范
围
检查
PC
软件
电平
GA
IN
是否
处在
合适
的数
值
检查
扬声
器是
否已
损坏
功放
不停
的开
关
检查
功放
接地
线是
否接
触良
好
检查
蓄电
池接
线端
子和
电源
端子
是否
接触
良好
检查
蓄电
池电
源电
压是
否过
低
遥控
开关
机的
连接
线接
触不
良
故
障
检测
方法
一个
声道
不工
作
检查
此声
道的
音频
信号
线的
连接
情况
检查
此声
道扬
声器
输出
端子
的连
接情
况
检查
音源
声道
平衡
调节
器是
否调
整到
中间
检测
此声
道对
应的
扬声
器是
否损
坏
检测
PC
软件
是否
将一
个声
道静
音
13
Symptom
Possible Remedy
Amplifier
will not
power up
Check to make sure you have a good ground connection.
Check that there is battery power on the (+)terminal .
Check all fuses, replace if necessary .
Make sure that the Protection LED is not illuminated.
Protection
LED Comes on
Check for short circuits on speaker leads.
Check the speaker load not beyond the minimum load.
Remove speaker lead, and reset the amplifier. If the protection LED still
Comes on, then the amplifier is faulty and needs servicing .
No output
Check that the RCA audio cables are plugged into the proper inputs.
Check all speakers wiring.
Check the headunit output and the amplifier level setting.
Low output
Reset the level Control.
Check the Crossover Control settings.
High hiss in
The speakers
Check the RCA cable is not shorted to power ground at amplifier side.
Check the amplifier grounding.
Distorted sound
Check that the Input level control is set to match the signal level of the head unit. Always
try to set the Input level as low as possible.
Check that all crossover frequencies are properly set.
Check for short circuits on the speaker leads.
Amplifier gets
Very hot
Check that the minimum load impedance for the amplifier model is correct.
Check that there is good air circulation around the amplifier. In some applications, It may
be necessary to add an external cooling fan.
TROUBLE SHOOTING
If your amplifier is still malfunction after checking through the troubleshooting
section, please contact our authorized SOUNDMAGUS dealer.
SPECIFICATIONS
Table 1
Table 2
MODEL
CHANNEL
RMS@4Ohm
RMS@2Ohm
Mas Power
DIMENSIONS(mm)
(L) x (W) x (H)
SE90.2
SE150.2
SE90.4
SE150.4
2
2
4
4
80W x 2CH
135W x 2CH
80W x 4CH
135W x 4CH
120W x 2CH
160W x 2CH
120W x 4CH
160W x 4CH
Bridged
@4Ohm
230W x 1CH
320W x 1CH
230W x 2CH
320W x 2CH
480W
640W
960W
1280W
243 x 202 x56
263 x 202 x56
313 x 202 x56
380 x 202 x56
320W x 1CH
580W x 1CH
660W x 1CH
580W x 1CH
550W x 1CH
980W x 1CH
1150W x 1CH
1150W x 1CH
MODEL
CHANNEL
RMS@4Ohm
RMS@2Ohm
Mas Power
DIMENSIONS(mm)
(L) x (W) x (H)
SE800.1
SE1500.1
SE2000.1
SE3500.1
MONO
MONO
MONO
MONO
3100W x 1CH
1600W
3000W
4000W
7200W
351 x 202 x56
428 x 202 x56
445 x 202 x56
588 x 202 x56
RMS@1Ohm
RMS@0.5Ohm
800W x 1CH
1400W x 1CH
1900W x 1CH
1900W x 1CH